Worn bearings in a washing machine drum
Over time, due to moisture ingress, the bearing begins to rust and deteriorate. In the initial stages, the machine makes an iron grinding; in case of more serious damage, this leads to a free lateral movement of the shaft with a drum and strong vibration during spinning. It is highly discouraged to use such a machine, because the bearing needs to be replaced! If it “scatters” during operation, the fragments will seriously harm other parts of the unit.
Decision: replace the bearing. Self-replacement is not recommended because it is a laborious and experience-intensive process. Use the services of a specialist.
Unstable support on the floor
The washer must stand firmly on a hard floor. If the floor is plank and bends, there is a strong vibration and the car jumps. Check the feet under the washing machine. In the process, they are unscrewed, which leads to instability.
Decision: secure each leg with a lock nut.
The attachment for the washing machine is loose or the counterweight itself has begun to collapse, so the washing machine vibrates strongly. The counterweight is a heavy unit that also prevents vibrations, keeping the unit stable. It is made from concrete or plastic.
Concrete counterweights crumble and collapse over time. But more often there are problems with fastening. they get loose, there is a characteristic knock and vibration.
Decision: it is necessary to adjust or replace the mounting bolts or the counterweight itself.
Why does the washing machine jump?
. 6 reasons the washing machine vibrates when spinning
Was the washing machine vibrating violently during spinning, jumping or moving? The reasons are hidden in its malfunction or incorrect installation.
Shock absorbers for the washing machine broke
Shock absorbers for washing machines (dampers) exclude tank vibrations, preventing impacts on the body. Always used in washing machine in conjunction with spring mechanisms.
It is easy to check the shock absorber: pull the tank towards you with the car door open and release it. If it snaps into place, the springs are serviceable. When waving from side to side, the shock absorbers will have to be changed.
A defective shock absorber is the breakage of the plastic covers that fit the tubes or plates extending from the tank. These elements are one piece with the tank and transmit all vibrations to the plastic covers, which are tightly pressed against the tubes or plates using U-shaped metal rods that are attached to the body of the washing machine tank.
Decision: to replace the plastic covers, disconnect the shock absorber of the washing machine (damper) from the body by unscrewing a few screws and removing it from the mount. Remove cracked or broken covers and install new ones.
To install new covers, it is necessary to unclench the U-shaped metal rods, securing one of them, for example, with the foot of the foot, and take the other off by hand. Insert new covers between the rods and pull them back, loosening the tension.
Shipping bolts not removed
It happens that when installing a new washing machine on your own, they forget to remove the transport device, which fixes the drum inside the washing machine, so that it is not damaged during transportation.
Decision: during installation in working condition, the transport device must be removed, otherwise the fixed drum will vibrate strongly, which will lead to rapid wear of many components.
Uneven distribution of laundry in the drum
Loud noise and vibration of the machine during spinning sometimes occurs due to uneven distribution of the laundry in the drum, so the washing machine jumps.
Decision: stop spinning, lay out each piece of laundry so that it can be distributed in the machine before spinning.
Remember that a bouncing car can wreak havoc on your bathroom or kitchen environment. With strong vibrations, all machine components are subject to increased stress. The washer will gradually break down, which means that a more complex, lengthy and expensive repair will be required.
The oval tank of these machines, unlike the round ones, saves water, electricity and even powder consumption.
See the spectacle of how effectively the washing machine “scatters”
Rubbish and foreign objects
If you hear an unusual ringing, noise or grinding noise during washing or spinning, the reason may be that some foreign object has got into the tank. This often happens when the hostesses do not check their s too carefully. These items can include nuts, coins, paper clips, bra bones, metal buttons, and so on. What to do? How to eliminate extraneous noise?
We’ll have to tinker. In order to look into the tank, you need to get to the Tubular Heater and unscrew it. Through the hole formed, using long tweezers or simply with your fingers (if possible), get objects that make an extraneous sound. Now you need to put the Tubular Heater back in place, remembering to clean and degrease the rubber seal. It can be lubricated with e.g. liquid detergent.
Sometimes the problem is much easier to solve. Some models of “washing machines” have a special sump in which a filter is installed. In this case, you just need to open the sump door. It is most often located in the front. Now we just take out the filter and shake out everything that gets into it.
Sometimes, when the “washing machine” hums and makes noise during the drainage of water, the reason may be damage to the drain pump. You can try to remedy the situation by cleaning the mesh filter. It is located on the front side of the unit, behind a special cover.
You also need to make sure that the drain pipe is clean. This is another reason why the car began to make noise. Clean the pipe, the noise is likely to disappear.
If all else fails and the unit still buzzes and rattles, it’s a bad thing. The drain pump is completely out of order and will have to be replaced. In order not to make a mistake, listen carefully to the operation of the unit. The pump can be “suspected” only when the “washing machine” makes noise only during water collection or when it is drained, and the rest of the time it works quietly. The sound will be very similar to how a working transformer makes noise.
Why does the washing machine make a lot of noise during spinning
No washing machine, like any other technique, can last forever. If your home assistant is more than 5 years old, the likelihood that she will break down rapidly increases. If the machine, which usually runs quietly, suddenly begins to screech and hum like a fighter on takeoff, you need to urgently take action.
These rather heavy elements of the washing machine hold the tank in place during the spin cycle. They are designed to extinguish the centrifugal force and resist the rocking of the “washing machine”. If you hear a lot of noise or rather a rumble when spinning from the drum, check the counterweights. They are made of concrete, and it tends to deteriorate from old age.
Unscrew the back panel of the washing machine and carefully inspect the counterweights, wiggle them. If the fasteners are loose, tighten them by tightening the corresponding bolts. If you find cracks on any of the counterweights, it is better to replace it completely. If this is not done, then the counterweight can split from strong vibration and damage the internals of the unit. Then you will have to repair a lot more.
See also. Shock absorbers for washing machines: DIY repair and replacement
It so happens that during operation, and especially during spinning, the washing machine whistles. At the same time, you find rubber shavings on the cover or walls of the hatch. Most likely, the matter is in the seal. Most often this happens with inexpensive models of “washing machines”.
Of course, it is best to replace the seal and find a new one that is the right size. But you can try to solve the problem with the advice of folk craftsmen. Take a small piece of sandpaper, insert it between the front wall and the sealing rubber. Now run any wash cycle of at least half an hour. There is no need to put in linen. The sandpaper will help fit the gum to size. You just have to take it out and remove the rubber debris from the machine. To do this, run an additional rinse cycle, then clean all filters.
The most common causes of ambient noise
There is nothing particularly complicated in the device of the washing machine. Therefore, there are not so many places where a malfunction can nest. It all depends on at what stage of the wash unusual noise and rattling occurs. The reasons why a lot of noise is heard may be:
- The bearing installed in the drum drive has become unusable.
- The fastening bolts holding the tank during transport have not been removed.
- Loose drive pulley.
- Counterweights holding the drum loose or crumble.
- Some small objects got between the drum and the tank wall and got stuck there.
- The drain pump has broken.
- The rubber seal located on the manhole cover is crumbled or does not fit.
- Washing machine is not level.
See also. Why does powder remain in the washing machine tray after washing
Incorrect installation of the washing machine
Sometimes the answer to the question why the house washer rattles and rattles during washing, especially when spinning, is that it is simply not installed correctly. This is not about the electrical part, but simply about its physical location. If the unit is not installed evenly, then when rotating at high speeds, for example, when spinning, centrifugal force will unbalance it. This leads to the following consequences:
- there is a powerful vibration;
- the body of the machine sways or “jumps”, moving from place;
- you can hear a strong pounding and drumbeat.
To remedy the situation, nothing needs to be repaired. It is enough just to set the “washer” according to the level by twisting the legs. The sound should disappear.
If, after checking all the reasons described above, you still have not found the reason why the washing machine makes unusual sounds, it may be in the electric motor or the “wired” part of the unit. Here you cannot do without special skills. It is best to call the master. With the help of a multimeter, he will carefully “ring” all suspicious places and determine the cause of the unregulated sounds.
The pulley is loose
When the washing machine hums, makes noise, and clicks loudly as the drum rotates, it could be because the drive pulley is loose. It’s easy to check. Turn on the machine in test mode. If this is not the case, a hand wash mode or any other mode in which the drum rotates slowly is suitable. Listen carefully to the sound while looking at the drum. If at each turn you hear an extraneous noise, or rather, a click, most likely the pulley is to blame.
It’s easy to fix the situation. Remove the back panel, locate the retaining nut that holds the pulley in position. Using a wrench of a suitable size, remove the backlash by tightening the nut until it stops. If the spinning noise disappeared, then you did everything right. If not, we continue to search.
This is a fairly complex breakdown, and you need some skills to fix it. But it is not difficult to find it. It is necessary to disconnect the “washing machine” from the mains and scroll the drum by slightly pressing on it. Rotate clockwise first, then counterclockwise. If the stroke is intermittent, whistling, knocking and rattling are heard. you can rest assured that the point is in the bearings.
There is another way to detect the problem. The fact is that a leaky oil seal leads to damage to the bearing. When it is damaged, water gets further, the bearing rusts and crumbles. You can see this by unscrewing the back panel. In the middle of the tank, with such a malfunction, rusty streaks usually appear.
If the cause is found, it must be corrected as soon as possible. The operation of a washing machine with crumbled bearings ends in damage to the sleeve and the shaft on which the drum sits. All this only exacerbates the problem and increases the cost of repair.
See also. Bra bone got into the washing machine
Washing machine noise standard in decibels
It is indicated in the characteristics of the machine and may differ slightly depending on the brand and model of equipment. In most modern washing machines, the permissible noise level does not exceed 55 dB (decibels) for washing and 70 dB for spinning.
What is 50-55 dB? This is loud human speech or background music sounds. Noise level of 80 dB. noise like from a large highway. Thus, there is no need to talk about the complete noiselessness of the machines. But if you close the door to the room where such a machine works, the sounds really will not interfere with you.
Why is the washing machine making a lot of noise?
- The washer makes a lot of noise during spinning, vibrates or even “jumps”, thereby creating an additional rumble.
- When draining water from the machine, loud sounds are emitted by the drain pump.
- The machine makes noise at any rotation of the drum: during washing, rinsing, spinning, and even if you just turn the drum by hand.
- There is a lot of noise when drawing water.
Does this always indicate a breakdown? Let’s figure it out.
Washing machine makes noise due to improper operation
Overloading, underloading or uneven distribution of items in the Washing machine can result in loud noises during the spin cycle. Be careful, read the instructions for the washing machine and follow the rules regarding the weight and size of the loaded laundry. This will not only save you from increased noise, but also extend the service life of the equipment.
Note! Underloading the washing machine or washing one large and one small item is no less dangerous than overloading. Since in these cases the washer cannot distribute the load evenly throughout the drum, it “dangles” more than necessary during the spin cycle and creates loud noises.
When noise is a reason to think
You should start looking for reasons why your washing machine is making noise if:
- there were extraneous sounds that were not there before: crackling, crashing, creaking, whistling, grinding and others;
- the noise has increased compared to what it was before;
- there are other signs of a malfunction of the washing machine, in addition to increased noise, for example, the machine has stopped squeezing or draining water.
Technology can make sounds. this is normal
It should be understood that the washing machine, like any unit, still creates some sounds during operation. In particular, you may hear:
- the sound of pouring water when it is typed;
- the noise of a working drain pump (pump) when draining water;
- the sound of the engine when the drum rotates;
- drum noise at high speeds during spinning;
- clicks if the machine switches modes, for example, goes from the washing phase to rinsing, etc.;
- water heating noise, like in a kettle, during washing.
Don’t worry, these sounds are not breakage.
If a new washing machine makes noise
So the reason is incorrect installation. The following situations must be excluded:
- The transit bolts have not been removed. When you start a new washer, for which you forgot to remove the transport bolts, you will hear a loud noise even during washing. If you do not interrupt the cycle, during the spin cycle the machine will make a very loud noise and “jump” on the floor, and after washing the drum will be damaged.
- The machine is installed on an uneven surface. Check if the washer is level. If not, level it.
- The machine is in contact with a wall or other interior item. There are no uniform standards on this issue: some manufacturers say that the minimum gap between the machine and the wall should be at least 5 cm, others. at least 1 cm. Craftsmen recommend leaving at least 2 cm.
- Wobbly floor under the car. An insufficiently stable floor leads to increased machine vibrations. If it is not possible to change the location of the unit, local reinforcement of the floor is required.
Everything is fine, but the noise from the new washer is still too loud? Check the instructions for what level the manufacturer claims. Often, buyers do not pay attention to this characteristic and, if the previous car made different sounds, they think that something is wrong with the new car.
Note! If the noise level in the new Washing machine does not exceed the one declared by the manufacturer, it is pointless to contact the service center under warranty. These are the initial characteristics of your machine.
LG washing machine with direct drive makes a lot of noise during spinning
Separately, it should be said about LG washing machines with direct drive 2008-2012 years of release. Due to the design features (the absence of a motor at the bottom, which was an additional counterweight), these models vibrate quite strongly during spinning. In particular, many users complain that the cars “jump” on the floor, despite observing all installation rules, and make a lot of noise. The only solution to this problem is to install an additional counterweight from the bottom of the drum.
Breakage due to which the washing machine rattles during spinning
The cause of the breakdown can be determined by how much noise it makes, and how loudly the structure hummed during operation. The sound can be in the form of a squeak, knocking, hum, vibration, the sound of pouring sand.
It is equally important to establish the moment when the manifestation of sounds specifically begins, or, to be more precise, the phase of the cycle during washing.
It is very easy to contact a specialist, but sometimes it is worth servicing not small funds, and therefore it is worth trying to determine and remove the malfunction yourself. Initially, you need to clean the components of the washing machine, such as the cuff on the hatch, the filter.
- It is necessary to inspect the water supply and drain hoses for pinching.
- The washer must be installed on a hard surface and, if there is no support on 4 legs, then you need to put the material to maintain the optimal level.
- It is very important to carefully follow the recommendations from the manufacturer regarding washing, which will extend the life of the device and keep the clothes in their best shape.
- It is strictly forbidden to overload the drum, as very much or very little content will lead not only to knocking, but also to wear of the bearings.
- The mode must be selected, depending on the type of washing.
- It is undesirable to wash things that have decor made of solid objects. If washing is necessary, they must be wrapped inside the product.
- Before washing, you need to check the s to prevent coins and paper clips from getting into the tank cavity.
As a rule, noise begins to occur during spinning, when the drum rotation speed increases to a maximum, and in rare cases, it is considered normal that the product rumbles when water is collected.
Root reasons: why the washing machine hums when spinning
It is worth noting that there are a number of moments when it is really impossible to do without the help of a specialist. As a rule, it is worth contacting it if the engine, drum, or other internal part knocks.
It is categorically undesirable to disassemble the washing machine and diagnose with improvised means without not only having education, but also experience with such equipment.
It is very likely not only not to find the cause of the breakdown, but also to worsen the general condition of the device. If you ignore the signs of a washing machine breakdown, then you should prepare for a serious repair with a large investment or for the purchase of a new product. It is quite possible to postpone the repair for some time, but on the condition that the structure will not be used. Otherwise, problems cannot be avoided.
- Knocking when draining water;
- Noise when heating water;
- The presence of a loud buzz in the rinse mode;
- Breakdown current in contact with the case.
Sources of noise in the washing machine when the drum rotates
The hum from the beginning of the wash, as already noted, is quite normal for any operating motor of the washing machine, especially when spinning and draining the water. To identify a breakdown, you need to pay attention to the feature of the emerging sound, which will also help determine the type of malfunction.
- Unnatural and ever-increasing;
- Very noisy when spinning;
- The presence of extraneous noise is pronounced, resembling clanking on metal or even strong blows.
Initially, when the machine starts to work noisily and a metallic crackle appears, you might think that it is from pieces of clothing that are made of metal and in contact with the drum surface.
This is quite normal, but if there are only bedding inside the drum, then you should think about finding a breakdown.
Repair specialists believe that absolutely any washing machine should make noise and thunder during spinning, as the speed increases, and with regular use, gradual wear of parts and removal of grease begins, which leads to such consequences. If there is no sound amplification during spinning, then one can only envy the owner of such a truly silent unit.
Reasons why the washing machine makes noise when spinning
You should not panic and rush to call the master, or even throw out the equipment, since you first need to establish the problem and when exactly the washing machine began to make noise. Knocking, humming or squeaks can start extremely unexpectedly and before starting the unit for the next cycle. Amplification of sound begins gradually, and does not last for a short period of time. The washer after the purchase whistles and rattles.
In any of these cases, operation is undesirable, since the cause of the breakdown can be quite serious, and at the same time it can lead to a complete malfunction of the equipment.
If the machine hums and rattles at the first wash immediately after the start-up, then you need to contact the warranty service to diagnose it. This indicates that the device is defective from the manufacturer, could be broken during transportation, incorrectly connected or has breakdowns in the wiring.
Why does the machine crack when it works? The problem may lie in an illiterate connection, for which it is enough to use the operating instructions, and for this it is not necessary to contact the master. It is worth noting that there are models of washing machines that make noise, as this is the norm.
These include brand products:
In order to reduce the increased noise of work, it is enough to evenly distribute the laundry, load the device not completely, try to make the structure more stable. In other cases, the noise of the clipper may be a sign of a serious malfunction, but you can try to prevent it. It is especially important to pay attention to exactly how it works each time the product is started, so that a breakdown is detected before it will harm the device. In general, the machine rattles over the little things that can be found in the operating instructions. The transport bolts, which are required exclusively for transporting the structure, have not been removed. The bearing is broken. There is a foreign object in the drum, or it has entered the cavity between the drum and the tub. There is a problem with the drum pulley. No counterweight fixing, improper installation, pump replacement required, motor broke.
If the reason lies in the bolts, then the main thing is to detect and eliminate it in time, as it can lead to breakdown of the entire device. With careful fastening of the fastening bolts, the drum springs are fixed and, accordingly, washing without unscrewing will lead to their breakdown.
Noise in the washing machine during spinning
The washer is an indispensable assistant in everyday life, and therefore you need not only to purchase high-quality equipment, but also to correctly observe the operating conditions, which will extend the service life for a long time.
Washing machine jumps, vibrates, shakes
The washing machine is jumping. how to be Strong vibration of the washing machine, when it shakes during spinning, this is a signal of a malfunction or incorrect installation. There are many reasons for this.
- the washing machine vibrates strongly during spinning;
- the washing machine jumps and moves during spinning.
Why does the washing machine jump?
- Unstable support on the base (floor).
- Failure of shock absorbers.
- Looseness of the counterweight or destruction of the counterweight.
- Transport device not removed.
- Laundry imbalance.
- Worn bearings.
Disconnect from electricity. Disconnect the washing machine from the mains.
Stability on the floor. First of all, you need to check the stability of the washing machine, it must stand firmly on the base. The floor on which the machine is installed must be solid and monolithic, if the floor is plank and bends, vibrations will occur.
Then check the legs, they are usually adjustable, and sometimes, during operation, they are unscrewed and this leads to instability. To avoid this, you need to secure each leg with a locknut.
Shock absorbers or dampers. Check shock absorbers for wear. To do this, access them by disconnecting the back cover or the front wall of the washing machine. The actual shock absorbers or dampers are installed on the washing machines. Shock absorbers have a certain “stroke”. They are designed for a certain force, which corresponds to the model of the washing machine on which they are installed.
Defective shock absorbers do not provide the required force. You can check this by disconnecting one of the ends of the shock absorber mounting and checking it manually. A defective shock absorber has a light “stroke”, which leads to increased vibration during the spin. Shock absorbers are fastened with bolts or plastic bushings on latches, one end to the bottom of the machine body, the other to the tank. To dismantle them, you need to unscrew the nuts and pull out the bolts or pull out the plastic bushings after sinking the latches, then insert new shock absorbers and repeat the reverse operation.
Dampers do not have their own “stroke”, but provide it due to the movement of a tube or plate, rigidly attached to the tank, in the damper covers. Damper failure is most often expressed in the breakage of the plastic covers that fit the tubes or plates extending from the tank. These elements are one piece with the tank and transmit all vibrations to the plastic covers. The covers, in turn, are tightly pressed to the tubes or plates using U-shaped metal rods that are attached to the body of the washing machine tank.
To replace the plastic covers, you need to disconnect the damper by unscrewing a few screws from the machine body and removing the damper from the mount. Next, remove cracked or broken covers and put new ones. To install new covers, it is necessary to unclench the U-shaped metal rods, securing one of them, for example, with a foot, and take the other off by hand. With the other hand, insert the plates between the rods and bring them back, releasing the tension. Installation of dampers is carried out in the reverse order, taking into account the individual characteristics of a particular model.
Attachment of counterweights. Check the condition and attachment of the counterweights. They are bolted to the washing machine tub. They are plastic and concrete. Problems usually arise with concrete, it happens that over time they crumble or crack.
Also, due to improper loading of laundry and the occurrence of increased vibrations, the fastening bolts may loosen. All this leads to the fact that the washing machine jumps on the spin, shakes and accelerated wear of other components of the washing machine occurs.
Transportation devices. There are times when, when installing a new washing machine on your own, they forget to remove the transport device. It fixes the drum inside the washing machine so that it is not damaged during transportation. During installation, the transport device must be removed, otherwise the rigidly fixed drum will vibrate strongly, which will lead to rapid wear of many components. Therefore, if all of the above reasons are not confirmed, we check the shipping bolts.
The importance of loading correctly. An imbalance in the laundry caused by uneven distribution before spinning sometimes causes increased vibration and shaking. This sometimes happens if the laundry is loaded carelessly before washing, “lump” or due to overload. In this case, you need to stop spinning, lay out each piece of laundry so that it can be distributed in the machine before spinning. As for the overloading of the laundry, in this case it is even worse washed because it does not have the opportunity to rub against each other, but rolls around with a ball inside the drum.
Bearing wear. Severe bearing wear can cause excessive shaking of the washing machine. At first, worn out bearings begin to make noise, and then gradually collapse, this leads to a free lateral movement of the shaft with a drum and strong vibration during the spin cycle. Further operation of such a machine will lead to a significant increase in the cost of repair.
The machine makes a lot of noise at the time of spinning, maybe we are not talking about a breakdown?
If the “washing machine” immediately after purchase and installation began to make a lot of noise in the spinning mode, this may be due to the factory characteristics of this model. In other words, the noise level at the most intensive stage of the “washing machine” operation is set by its manufacturer. Therefore, if there is a lot of noise with a new washing machine, study its passport. In the passport, the manufacturer often indicates the noise level, measured in dB, which the machine emits during the most intensive work.
In this case, the question arises, even if the washing machine makes noise during spinning and the noise level is indicated by the manufacturer in the passport, say 75 dB, how do we know that our machine reproduces the sound of the same strength. Indeed, it is possible to accurately measure the level of the noise reproduced by the machine only with the help of a special device. a sound level meter. If you have the opportunity to use it, that’s good, but more often than not, an ordinary hostess does not have access to such equipment. And how to proceed in this case?
The easiest way to measure the noise level of the car is the so-called associative method. On the Internet there are many examples of common, well-known sounds with data on their strength in dB. For example, the sound of a typewriter is 50 dB (distance 1m), a train in the subway is 95 dB (distance is 7 m), the sound of a jackhammer is 120 dB (distance 1m), and so on. Roughly compare the strength of the sounds you are familiar with with the noise made by the washing machine and you will understand whether the numerical values indicated in the passport correspond to reality or not.
Also, be sure to pay attention to the character of the sound. If a strong monotonous noise is interrupted by a clanging, metallic grinding or knocking, then most likely there is a malfunction in the washing machine and you need to take measures to eliminate it.
Description of the causes of noise and how to eliminate it
The reasons, features and nature of the noise of the drum of the washing machine are specific in each case. It all depends on the model of the washing machine, on the nature of the breakdown, the degree of wear of its parts, and the like. Therefore, we do not guarantee that you, according to our description, will 100% be able to diagnose the cause of the breakdown. In doubtful cases, it is better to consult a specialist.
Objects are stuck in the space between the tank walls and the drum. According to experts and consumer surveys, this is the most common reason for the loud noise emitted by the drum during spinning. When we, without hesitation, throw things into the drum of the machine, in the s of which small change, paper clips, pins and other small objects remain, there is a great risk of getting these objects into the tank of the washing machine. What is it fraught with?
At low speeds, the washing machine practically does not vibrate, and small objects lie quietly in the tub, without touching the rotating drum. But during the spin cycle, the machine begins to vibrate strongly and small objects begin to bounce and, in the end, get stuck between the tank wall and the moving parts of the machine. As a result, moving parts begin to whistle, creak and make other sounds.
To get to the objects that got into the tank, you need to unscrew the ten, stick your hand into the tank and pull out everything that got there, the problem will be resolved.
The bolts for transporting the machine have not been removed from the tank mountings. A gross but common mistake made by washing machine installers. The fact is that for a more careful transportation of the machine, the manufacturer has provided special fasteners that fix the shock-absorbing springs of the drum. If these fasteners are not removed, the drum of the washing machine will rotate with a loud clatter when the program starts. The problem is solved by unscrewing the four mounting bolts located closer to the middle of the back wall of the machine.
The drum drive bearings are damaged. The moving parts of the washing machine are equipped with several bearings. If one of the bearings breaks down, it will result in a loud noise, especially during intensive work of the “washing machine”. How to identify a bearing failure? Disconnect the washing machine from the mains, put your hand through the hatch and turn the drum first clockwise and then counterclockwise. If the drum cracks and knocks during rotation, then the problem is in the bearing.
You can read about how to properly change bearings in a washing machine here. But it is still better to entrust this work to professionals, especially if you have never repaired household appliances with your own hands.
Loose pulley, drum drive system. To determine the problem with the pulley, you must run the washing machine in a test mode. In this case, the drum will rotate, slowly making a dozen turns in one direction and a dozen in the other. At this moment, you need to listen to the typewriter, if you hear clicks, this is a reason to check the drum pulley. To fix it, you need to remove the back wall of the machine and, armed with a suitable tool, tighten the pulley fixing nut.
Machine counterweights are loose. Counterweights located around the tank of the washing machine serve to dampen the centrifugal force, which inevitably must swing it strongly. Typically, problems with counterweights arise after very long machine use or as a result of a factory defect. To fix the problem, tighten all loose connections holding the counterweights together. To do this, you will have to remove the back wall of the washing machine, for how best to do this, read the article Dismantling the washing machine.
The washing machine is not installed correctly. In this case, we mean placing the machine on the floor, and not connecting it to the water supply and sewerage system. When the drum rotates quickly (800-1000 rpm), the centrifugal force naturally tries to create an imbalance. If the machine is not level, on an unstable, sagging floor covering, this will result in:
- to the beat of the drum;
- strong vibration;
- rocking the body of the washing machine.
The problem is solved by strengthening the floor and installing the machine strictly according to the level. You don’t need to have a perfectly flat floor to level your clipper. You just need to unscrew the legs of the “washing machine” so that the body is level, for this you have to sweat a little, but it’s worth it.
The rubber seal on the sunroof is not adjusted to fit. If, when the drum rotates, a characteristic creaking or whistling sound is heard, and after washing, rubber chips are noticeable on its walls and on the hatch cover, the problem is in the sealing gum of the hatch. Unfortunately, the assembly of some budget models of washing machines leaves much to be desired, and gum is probably the last thing that collectors pay attention to.
The problem is easily solved. You need to insert a piece of sandpaper between the sealing rubber of the drum and the front wall of the machine and start the washing program without laundry. Sandpaper will smooth the gum in 20-30 minutes, as needed, and you just have to pull it out and remove the rubber chips from the drum by starting an additional rinse program and cleaning the filter.
Note! If a strong background sound is heard when draining water from the drum of the machine, the problem may be hidden in the drain pump.
How to change it yourself, read the article Replacing the drain pump.
The washing machine makes a noise during spinning. what to do?
If the washing machine hums when spinning, then you definitely need to understand why this is happening? It is possible that you simply purchased a too noisy model of a washing machine, or perhaps we are talking about a serious malfunction, which in the end will lead to a breakdown of the household appliance. In any case, it is worthwhile to figure it out and take measures to eliminate noise, and within the framework of the article we will try to tell you how to do this.
Typical causes of washing machine noise
The washing machine is relatively uncomplicated. Experts have empirically identified several main causes of machine noise during spinning caused by breakdowns. We list these reasons.
- Bolts for transporting the machine have not been removed from the tank mountings.
- Drum drive bearings damaged.
- Objects caught in the space between the tank walls and the drum.
- Loose pulley, drum drive system.
- Tank counterweights loose.
- The rubber seal of the manhole cover does not fit.
- The washing machine is not installed correctly.
Note! Be sure to notice at what point a loud noise occurs. At the start of a wash program, at the beginning of a spin program or during draining. this is very important for correct diagnosis.
How to prevent noise-causing faults in the future?
In order for the machine to serve for a long time and to avoid “noisy malfunctions” from time to time, it is necessary to follow the rules of its operation. The more carefully and prudently you treat your “home assistant”, the less often you will have to face such troubles. What operating rules are we talking about??
- Do not put more laundry into the drum of the machine than is intended by its design.
- To wear and tear of the parts of the machine (especially the sealing rubber), leads to its too frequent use (several times a day). The machine must have time to dry between washes.
- Use less frequent wash programs with very hot water and high rpm.
- Remove dirt from the drain filter as often as possible.
- Check s for foreign objects before washing, turn items inside out before putting them in the drum, and use laundry bags.
- Add water softeners before washing to avoid limescale deposits on the elements of the washing machine.
To summarize, we note that if your machine suddenly begins to rattle during spinning and restarting the washing program does not solve the problem, most likely there is a breakdown that needs to be found and eliminated. And valuable advice from experts will help us in this. Happy renovation!