Water Does Not Flow Into The Washing Machine Reasons

serious damage

  • Malfunction of the inlet valve, which is caused by a breakdown of the system of passage mechanisms that regulate the amount of water. You will have to remove the top cover from the machine. The inlet valve is located at the top. It is necessary to remove the pressure reducing rubber reducer, which can also be washed. But the main thing is to believe if the valve system is working. This can be done by disconnecting the terminals and applying current to the coil. The coil core will then be lifted. If this does not happen, then the reason is in the intake valve mechanism and it will have to be replaced.
  • A malfunction of the electronics that controls all the cycles is the reason due to which water does not flow or does not flow well into the washing machine. In addition to a malfunction of the main board, the reason may be that there was an open circuit at the entrance to the electronic control unit. Measure the signal coming from the electronic unit of the machine. If this is an open circuit, it can always be repaired.
  • Perhaps the electronics is faulty, this is the reason for the poor operation of the pressure switch (a device that corresponds to the level of water drawn into the system); it is not recommended to repair such a breakdown yourself. Having rummaged in the typewriter, looking at all possible causes and sources, you still do not understand why water does not enter the LG washing machine? Take a look. which is offered by experienced craftsmen to help non-professionals. Still not clear? In this case, call the master at home.

Water Does Not Flow Into The Washing Machine Reasons

If the machine is under warranty, there is no need to inspect it yourself. This will be done by the master who arrived on your call. You may have to take the washing machine to a service center.

Remember: Your actions to repair a car may void your warranty.!

How to fix

The door lock can be replaced by yourself, if you have certain skills; it’s a simple mechanism.

Sources of problems

Why isn’t water getting into the washing machine? It would seem that everything is simple, for a maximum of one or two reasons. However, the number of possible sources of such a malfunction will surprise you very much. The mechanism of water entering the drum is simple: the inlet valve regulates the flow of the required amount of water from the water pipe to the drum of the machine.

The intake filter mesh is clogged with rust from the riser. This often happens with an emergency shutdown of water for several days. At the moment when water is supplied again, debris and pieces of rust clog the inlet filter and water does not enter the machine;

The washing machine does not receive water: possible causes

Household appliances are always unpleasant for their owners. And the breakdown of the washing machine. even more so. We are so accustomed to daily quick cycles or Sunday big washings that we don’t even think about how much work it cost to wash in a simple Kyrgyzstan-type centrifuge.

The source of a washing machine breakdown cannot always be identified at a glance. You need to be an experienced craftsman with a lot of experience. Of course, 85.90% of breakdowns are the same for all washing machines, because their mechanisms differ little from each other. However, there are also unique ones, which depend on the individual operating conditions and characteristics of the washing machine.

In any case, it is useful to know the list of possible causes in order to be able to fix some of them yourself.

We will look at the stereotypical sources of malfunction of the washing machine in the event that it does not receive water.

How to fix

Unscrew the inlet hose, carefully, with a suitable tool, remove the inlet filter mesh, which is shaped like a thimble, rinse it if traces of contamination are visible. A clean filter is a signal that the fault is elsewhere.

  • Some models of machines, such as those produced by Samsung, are designed to be connected to both cold and hot water at the same time in order to save energy for heating. In this case, washing and rinsing come from different sources. If water does not flow into the washing machine drum, see if the water shutoff valve is open.?
  • Perhaps the water pressure in the water pipe is not constant or insufficient for the machine to draw water into the system;
  • Recently, various filters for cleaning the system have been installed to enter the water supply system into the apartment, and they are installed both on cold and hot water; it is possible that the filter at the inlet is clogged with debris and needs to be cleaned;
  • The door is not closed, the lock did not work, water does not flow and the automatic machine does not start a cycle, since the door lock is part of the system that protects against leaks; perhaps the lock tongue has shifted and is in the wrong position, preventing the door from slamming;
  • The door lock of the machine is broken, it does not close, therefore, a mechanism that protects against leaks is triggered;

Preventive measures

Everyone knows the rule. in order for things to serve for a long time, treat them with care. In the case of a washing machine, there are a few more mandatory rules. Which will help prevent some troubles:

  • Use the instructions. This is a voluminous copy, where your actions in a particular case are described in detail on several pages. The instruction will help to avoid elementary mistakes in programming the cycle, which means it will prolong the operation of the machine;
  • Many washing machine manufacturers, such as Samsung or LG, recommend doing a first test run after installation. The cycle is started without laundry to remove grease and dirt residues;
  • Do not try to save electricity by pouring heated water into the drum if it is not provided for this. This has a bad effect on the duration of the service life;
  • Do not load more than the recommended amount of laundry into the drum. This is fraught with more serious damage;
  • After washing, dry the machine and wipe off the rubber seal on the tank. Even if the machine is standing with the lid open, water may remain there, which over time will lead to the development of mold and fungi;
  • Use water softeners and anti-scale products; specialists of companies producing Samsung or LG washing machines strongly recommend not to wait until the machine is overgrown with scale, but to remove it in a timely manner;

Position the clipper so that it is as level as possible. Do not forget to remove the transit bolts beforehand.

What to do when the washing machine does not fill up with water

One of the private problems people face is that the washing machine does not fill with water (or water simply does not flow into the washing machine).

Before giving a couple of practical tips on how to react in such a situation, it is worth noting that most modern washing machines are filled only with cold water, so it is advisable to skip all the nuances regarding problems with the hot water valve on the washing machine.

Let’s get back to the problem under consideration. In most cases, the most common reasons for the lack of water in the machine are kinks in the water supply hose, or a malfunctioning tap (when the valve inside does not actually turn when it is turned on). Another common reason is the accidental shutdown of the tap, in which people simply do not realize what happened. Other causes could be faulty electrical wiring, broken water valve, or malfunctioning software controls. These tips were originally compiled for those cases when washing machines were still common, in which both hot and cold water were supplied, and therefore some types of errors simply did not exist. This issue has already begun to be addressed by manufacturers of new washing machines, which are filled with exceptionally cold water and issue a certain error code, signaling that water is not supplied to the machine.

Today, most of the washing machines are controlled by special software, and therefore manufacturers set special error codes for situations when they do not determine the required water level during washing for a certain period of time. The wording of the error code for a non-water filled washing error should be indicated directly in the user manual. Here are some examples of typical breakdowns associated with a disruption in the water supply to the washing machine, which consumers most often deal with.

READ  Indesit Washing Machine Error Codes Without Display

Washing machine makes a strange loud noise when trying to fill with water.

Usually, in cases where the washing machine is unable to pump the required amount of water (or water in general), you may hear a strange hum that is not present when the machine is working properly. In such a situation, you should check whether the taps are turned on, whether water is supplied normally through the system in the house, and also see if the plumbing equipment (pipes, hoses, connectors, valves, etc.) has been damaged in any way. A slight noise coming from the back of the washing machine may indicate overvoltage in the valves when trying to pump water. In this case, it is advisable to immediately turn off the power to the machine, carefully move the washing machine, turn off the water supply to all pipes involved in the water supply. Then carefully disconnect the water supply hoses. At the same time, it is important to have some kind of bucket or other vessel and rag on hand, because at first the water remaining under pressure in the hose may well flow out. If water flows out actively for more than a second or two, the water supply pipes were probably not properly shut off or they are faulty. Hold the hose over a bucket or other container and turn on the tap again to make sure there is indeed a decent supply of water to keep the washing machine running properly.

Is the water supply working? In this case, it is worth checking the filter that is installed in the water supply valve in the washing machine. You can easily pull it out with a pair of pliers following the directions in the instruction manual and then clean it. It is the filter filled and clogged with debris in some (albeit extremely rare cases) that can cause insufficient water flow into the washing machine. Be very careful not to damage the fragile filter with the pliers. In case you made a hole in the filter. even a very small hole. this can allow sand and even small stones to enter through the water valve and damage the washing machine, possibly causing flooding.

Was the water supply insufficient to ensure the required passage of water through the hose? If water does not flow into the hose or its pressure is very weak, then the main cause of the malfunction is related to the water supply system, or there may be some kind of crease in the hose itself. If your washing machine was directly connected to the water supply with old pipes, in which too hard water can cause sludge formation and eventually the pipes can become clogged, then you should clean the holes or simply change the pipes. If this happened with pipes supplying cold water, then you can pierce them in a simple way: turn on the water supply at full power for a few seconds. but this option is absolutely not suitable for hot water pipes (namely, they clog more often). In this case, turn off the cold water supply completely and then drain all the water from the hot water tank with a thin stream, and then mechanically clean it.

If your washing machine was connected to the water supply and special blocking taps (red and blue) were installed, then in case of insufficient water supply, the malfunction may lie in them. Either you can actually forget to open them, or the valve inside the valve itself may lag behind and not react to the movement of the valve itself so that, assuming that the valve is on, you will not know that it is still blocking the flow of water. This usually happens when the red or blue valves are cracked. In this case, you can open them using pliers.

Household appliances repair at home. Semi-automatic washing machine repair

Despite the difficulty of disassembling these washing machines, repairing it yourself, such a miracle of technology, is not difficult, since if you understand this washing machine, there are only a few spare parts. Major breakdowns are related to the centrifuge. In this category you will find everything you need to repair yourself. There is a material where I talk in detail about how to change the oil seal and the centrifuge motor, where the condenser is located, how to replace the washing unit motor, and much more. In principle, a complete guide

Repair washing machine machine

If you have a minor breakdown, for example, such as a washing machine does not heat the water, then the principle of repair in all washing machines is practically the same, I am writing this so that you do not pay attention to the make and model of the washing machine. The main thing here is to correctly diagnose the breakdown, that is, to calculate what exactly failed, if it is some kind of part, then it will not be difficult for you to replace it yourself, but as for the control unit, then you will have to call the master. I do not advise you to go into complex elements.

Reviews of household appliances. Washing machine error codes

A very important section that will help determine the malfunction of your washing machine. Almost all washing machines that are equipped with an electronic control module have a self-diagnosis function, thanks to which an error code is displayed on the control panel, which indicates the direction in search of a breakdown. There are small nuances here, the error code does not always indicate the exact part that broke, so the wizards check all the peripherals that are associated with the spare part to which the control module indicated. For example, if the code indicates a malfunction of the Tubular Heater, this is not always the case and often the culprit is not the Tubular Heater, but the Tubular Heater relay on the control module. In this category, a complete decoding of the malfunctions of washing machines is given, I hope this will help not only professional craftsmen, but also ordinary people who seek to repair their washing machine without calling the master at home

Download the instruction manual for the washing machine

This section contains a lot of operating instructions for washing machines. I want to draw your attention to the fact that all instructions have been uploaded to the Yandex disk. If you are a resident of Ukraine, it is advisable for you to install a Yandex browser on your computer, with its help you can easily download any manual from my website. It is important for a simple layman to understand that the instruction is not just a piece of paper in which something is written. The operating manual will help you use your washing machine correctly, very often error codes are written in this manual, thanks to which you can eliminate minor malfunctions in your machine. Read carefully, study, I hope you find your model

Malfunctions of No Frost refrigerators

There are two types of refrigerators with a similar defrosting system, we are talking about a control system. The cooling system itself in these refrigerators is practically no different, but the sensors and dampers have a significant difference. Refrigerators with a know-frost system are repaired very simply, since it is mainly the electronic or mechanical part that fails, and such a breakdown as a freon leak is extremely rare. The main thing here is to establish the cause of the malfunction. It is not difficult to change a sensor or electronic module, but you will learn how to determine what is out of order in this category

Household appliances repair

The washing machine does not draw water

Washing machines, like any other type of equipment, tend to break down. As a rule, such malfunctions take us by surprise. So you threw the laundry into the washing machine, filled in the powder, closed the door and started the program. And the washing machine does not draw water or draws water, but slowly, what to do in such a situation? We will tell you about the causes and solutions for this problem. And the first thing we would like to recommend to you is not to panic.!

If you notice that no water is drawn into the washing machine, you must stop the washing program and disconnect the appliance from the power by unplugging it. See further below for possible causes of failure.

The washing machine does not collect water well. reasons

If the washing machine draws water, but very slowly, then the reasons for this may be different. Also, the reasons that relate to this behavior of the machine may serve as a complete cessation of the water supply. Those. If your machine does not collect water at all, then see also these reasons:

Weak water pressure

If water flows slowly into the washing machine, then check the water pressure from the tap. Maybe he’s just weak. Also check the water inlet to the washing machine, it may not be fully open. If everything is in order, and the water still does not go well into the washing machine, then read on.

The door of the loading door is not closed

The washing machine has a lot of different protections, one of them is that when the door for loading laundry is open, water will not be supplied and the washing program will not start. First, make sure that the door is tightly closed and not loose. To do this, close it tightly with your hand.

READ  How To Clean The Washing Machine From Mold

If the door does not lock when manually closed, then you have a broken locking tab on it, or the latch that is located in the lock of the washing machine body. The tongue may simply be skewed, this is because the stem falls out of it, which serves as a fastener.

This happens due to the fact that over time the door hinges weaken, and the hatch warps. In any case, you will need to align the door or disassemble it to insert the stem. Also, if the lock itself is broken, then its replacement is necessary. Take a look. where the repair of the door lock is clearly demonstrated:

The second problem that may arise with not closing the hatch. This is not a working door lock. The fact is that in any washing machine, the hatch is blocked before washing in order to protect you. If the machine cannot lock the door, then it will not start the washing program, which means that water will not be drawn into the machine.

The water supply to the washing machine is turned off

The first thing to check is to see if the water supply to the washing machine is open. Usually it is placed in the place where the rubber hose from the washing machine is connected to the pipeline. This is what it looks like: In the photo, the tap is open, make sure you have it open as well. To do this, the lever that opens the tap must be located in the direction of water movement, i.e. along the hose.

Broken water inlet valve

The inlet valve is responsible for supplying water to the washing machine. When the programmer sends a signal to it, the valve opens and water is supplied to the machine. When a signal comes that there is already enough water, the valve shuts off the water. A kind of electronic faucet. It turns out that if the valve is not working, then it will not be able to open itself and we will not see water in the washing machine. The easiest way is to ring it, because most often the coil burns out at the valve. It is located behind the washing machine, and the inlet hose is screwed to it.

If the water supply valve is broken, it should be replaced.

The washing machine does not collect water at all. reasons

If you started the washing machine by choosing a washing program, and water does not enter the washing machine at all, then any of the following breakdowns is possible. Check the machine on them in order to determine the exact cause.

No water or low pressure

The first and most commonplace situation is when there is simply no water in the tap. Unfortunately, this happens very often in our country. Therefore, if you notice that water does not flow into the washer, then in order to exclude this reason, open the tap with water. If there is no water, or the head is too small, then consider that the reason is established.

To solve it, you need to call your ZhEK and find out the reasons and terms of troubleshooting. In any case, you have to wait for them to fix everything and only then continue washing.

Clogged inlet valve filter

A filter is located in front of the inlet valve, which is a fine mesh. It is needed to retain large particles that are present in the water. Over time, this filter becomes clogged and the washer does not collect water well. In order to eliminate this option, you need to clean the inlet valve filter. Read on our website how to do it.

If the machine did not collect water well because of this malfunction, then the problem is easily solved. If the filter is not cleaned in time, then over time it will clog completely, and the machine will stop letting water through at all.

Also, the reason may be a clogged additional water filter for the washing machine, which you may have installed in front of the inlet hose. if you have one then check it.

How to determine if the machine cannot fill water

When the laundry in the drum is dry, the Washing machine hums and does not spin the drum, the breakage is clearly visible. But there are situations when there is water in the drum, but the wash does not start and it is not clear what happened. It may also be that the water flows too slowly and the machine identifies this as a breakdown. In this case, the display shows a fault code. Washing machine without display will report a breakdown by flashing lights.

For example, if the Indesit washing machine does not draw water, the combination H20 appears on its display. The same code is displayed in the Washing machine Ariston and Hotpoint Ariston. Electrolux and Zanussi units issue message E10 or E11. The following information appears on the displays of other brands of washing machines:

  • Samsung. E1;
  • LG. PE or IE;
  • Bosch. F01 or Aquastop;
  • Whirpool. FH or F1;
  • Candy. E02;
  • Asko. E01 or Water inlet fault.

If there is no display, the malfunction can be recognized by a combination of flashing indicators (for each brand of Washing machine it has its own, you can find it in the instructions for use).

Feeding problems

The reasons, as a consequence of which the washing machine does not fill with water, are elementary, for example, the intake tap is closed. Then the wash is not even started by the triggered protective automatic equipment. It is necessary to open the tap and start the washer again. But perhaps repair work is underway, so the water or low pressure is turned off in the house. In this case, you need to wait for the completion of the repair, and then continue washing. It is also recommended to inspect the supply hose. it may be damaged or clogged.

Door problem

Failure of the door lock-blocker or loose closing of it leads to the fact that the electronic system will pause the washing process. When using washing equipment, the metal door hinges and the plastic guide are worn out, which prevents the hatch from being fixed in the “Closed” position. The blocking system from unintended opening of the hatch also breaks down during the operation of the washing machine. This is the reason for the launch of the protective mechanism, which blocks the access of water to the drum.

Water does not flow into the washing machine

Home appliance users face a problem when the washing machine does not draw water. Happens both at the beginning of the wash cycle and during. This indicates minor malfunctions in the control system, and can also be a serious breakdown. There are several reasons why little water enters during washing or even its access is impossible in the washing machine.

Control unit malfunction

If the Washing machine does not pick up water or wash it, the ECU may be faulty. For example, its electronic board may not give a signal to turn on the inlet valve. It so happens that the ECU “jams”. Then you need to remove the plug from the outlet and wait about half an hour. If restarting does not correct the situation, you will have to call the wizard to diagnose the malfunction.

In most cases, problems with water supply to the Washing machine can be repaired by yourself. According to statistics, the banal lack of water and blockages are most often the cause of this phenomenon.

Pressure sensor does not work

A breakdown of the pressure switch does not allow the machine to pour water into the system, the sensor will signal a full tank, due to which the filling is not performed (the inlet valve stops opening), or the drain into the sewer will begin. If this unit does not work, it also does not spin the laundry. Also, a malfunction of this sensor leads to the destruction of the Tubular Heater machine.

Drain pump in a cliff

It would seem. an unobvious reason for the lack of water supply. But the Washing machine has the following aLGorithm. if the machine cannot drain the water, then it should not flow. The automatic washing machine has a built-in fault diagnosis mode, which is expressed in informing users in the form of error codes.

If the drain pump is in a rupture, then water will not flow, and the display will show the corresponding malfunction. After replacing the pump, the problem will go away and the washing machine will work fully.

Damaged wiring

Manufacturers of washing machines are quite economical in their use of components. This often leads to the following situations:

  • The wires are pulled tight. Sometimes at an angle of 90 °. The result is a cliff.
  • The thickness is very small, and in case of overloads or voltage surges. damage.
  • The weak point is the terminal chips.

These breakdowns lead to the fact that the contacts are not supplied with electricity, and, accordingly, water does not enter the drum.

Important! Washing machine valves are permanently closed.

Reasons why water does not enter the washing machine

Before inspecting and checking the operating parameters of household appliances for water entering the working system, it must be disconnected from the electrical network and from the supply.

READ  How To Ground A Washing Machine In A Bathroom

If there is a lack of water, which is drawn into the machine during rinsing, the automatic system is triggered, and an error indicator is displayed on the electronic display of the control unit, signaling an insufficient liquid level, due to which the process stops. The user’s task is to find the reason why the washing machine does not pump water, to eliminate breakdowns, if possible, on their own.

Self repair

Most modern “washing machines” are equipped with a self-diagnosis function, thanks to which the user can see the exact error. The error code is highlighted on the display using light indicators. You can decipher this code using the instructions from the manufacturer, which lists all kinds of technical errors.

But even if the exact cause of the unit malfunction is determined, it is not recommended to disassemble the machine yourself. Ignorance of the design features of the automatic machine leads to serious consequences at the end of the hand-held “repair”.

Visit of the master to the house for the repair of washing machines

Repair of large-sized household appliances is considered difficult, since it is almost impossible to transport them to a service center on their own. That is why our masters come to your home. at the specified address. This is one of the main advantages of our company, thanks to which residents of the capital and the region can use the help of specialists any day.

Modern cars are equipped with a large amount of electronics, so its breakdown is included in the TOP-5 of the most common problems that happen with household appliances. It will not be possible to fix this problem on your own, since the lack of the necessary knowledge and special tools complicates the diagnostic process.

To call a specialist at home, the client can call the phone numbers indicated on the website or use the feedback form. Next, you will need to provide the following information:

  • Symptoms of equipment breakdown. this information is extremely important for a master who needs to understand what parts and devices to take with him.
  • Choose the day and time of arrival of the master.
  • Indicate the model of the “washing machine” and the year of its production (required to search for original components).
  • Leave the address to which the master should arrive.

All repair work is carried out in the presence of the owner of household appliances. If desired, he can follow the work of a specialist to make sure of his competence. When the repair is completed, the master checks the machine’s performance by running it in standard mode without load.

The cost of repairing a washing machine at home

The formed pricing policy includes the cost of the repair work performed, diagnostics and the arrival of the master at the specified address. The visit of a specialist in Kiev is free, for residents of the region, it is necessary to clarify the cost of the call.

Craftsmen use high quality original parts that are offered at competitive prices. We maintain cooperation with trusted suppliers, so the price of parts is quite affordable.

Correct connection of the machine

In order to avoid problems associated with the fact that water is not drawn into the machine, it is necessary to entrust its connection to the water supply to real professionals. Indeed, very often there are situations when an inexperienced user makes minor mistakes when buying new equipment even at the connection stage. As a result, the technician does not want to start the wash cycle.

Masters of the Stirka Servis company will help you make a high-quality and prompt connection, taking into account the main nuances of the machine’s location. It is recommended to install the machine as close to the water supply as possible. Thus, it will be possible to avoid the additional use of a huge number of PVC pipes.

In the process of selecting fasteners and other valves, you need to pay attention to the characteristics of the machine. After all, the fasteners presented are not universal and each manufacturer uses a certain size of spare parts.

At each stage of the work done, it is necessary to check the sequence of the completed processes. Calling the master at home, the owner of the equipment receives a lot of advantages, among which it is worth noting: correct connection, start-up and testing of the machine’s performance, specialist advice. Thus, in the future, there will be no problems with the water supply.

Washing machine repair service

If your washing machine does not collect water, Stirka Servis will help you quickly fix the problems that have arisen. Repair is carried out by specialists with sufficient work experience, who have repeatedly encountered various breakdowns of household appliances. Main advantages:

One of the important advantages is the arrival of the master at the specified address, since the user does not need to deliver the broken equipment to the service center.

One of the most popular problems is a broken hatch lock

When the control panel does not receive a corresponding signal from the door locking system to close the hatch tightly, the machine “refuses” to draw water and wash things. This is due to the fact that during the closing of the hatch there is no necessary click, which should start the usual operation of the equipment. The most popular reasons for a malfunction of the sunroof locking system:

Various small foreign objects enter the hole where the latch tab fits. To do this, it is recommended to thoroughly clean the hole from accumulated dirt.

Breakdown of the control module, as well as the electronic board, is one of the most difficult problems, since to solve it it is necessary to replace components and re-solder the block tracks.

If the plastic door guide has been broken. In this case, the tongue will not be able to enter the desired hole. This is due to the deterioration of the hinges, which occurs during the prolonged operation of household appliances.

The set of the latch tongue contains a special rod, which, if used carelessly, can fly out.

The lack of a hermetically sealed door is due to its noticeable skew to a certain side. Craftsmen note that this problem occurs due to the fact that the loops weaken over time and lose their usual strength. This also occurs as a result of the frequent start of the wash cycle and the subsequent spinning of the laundry at high speeds. Breakage of loops happens due to the user’s carelessness: when loading a large number of items into the drum.

Regardless of the exact reason for the breakdown, it is recommended to call a wizard who will help fix it. This is especially true of machines, the operating life of which is more than 10 years.

Call a repairman for a washing machine in Kiev

In the absence of water in the drum, first aid will be required, which is provided directly by the owner of household appliances. It is necessary to close the water supply valve and unplug the machine from the outlet. Only after that you need to call the wizard. Sometimes the absence of water in the unit is accompanied by the presence of a characteristic buzzing sound. Therefore, the wizards perform the following mandatory tasks:

Check the valveThe valve that regulates the fluid supply must be in the closed position.
Disconnect the hoseAt the back of the structure, you can see a hose that needs to be disconnected. To do this, the owner must prepare in advance any deep container, so when unscrewing the remaining water flows down.
Check the hoseA specialist carefully examines the entire length of the hose for visual damage.

If, after carrying out the mandatory check procedure, all the parts were in order, then you need to proceed to the second stage. filter diagnostics (mesh made of metal). This filter is located on the filling hose, so all kinds of small elements can accumulate in it: dirt, threads, remnants of undissolved powder, etc.

Water does not flow into the washing machine

During prolonged operation of the washing machine, users may notice that the unit began to collect water poorly or does not collect liquid at all for further washing. Disrupted water supply is one of the most common symptoms that the device needs to be repaired.

To resume the previous work, you will need to organize a thorough diagnosis, which will help determine the real reason why water does not enter the washing machine. It is necessary to call the master even if the liquid enters the drum very slowly.

Repair services for washing machines

The Stirka Servis company will help to solve one of the most frequent problems faced by every third owner of household appliances: why water does not flow into the washing machine. An independent visual inspection of the unit will not bring the desired results, and all attempts to disassemble the case with your own hands often end in serious breakdowns of the “washing machine”. Therefore, the only correct way is to call an experienced specialist. Our masters perform the following types of work:

The time to complete the task depends on its degree of complexity. 80% of all breakdowns are fixed by the master on the day of arrival. The only exceptions are serious technical malfunctions, when additional equipment and auxiliary tools are needed. Sometimes delays are caused due to the lack of a required replacement part.