Washing Machine Samsung Errors How To Fix

What to do with the code “1E”?

As mentioned earlier, when the Samsung washing machine does not work, the lE error signals a problem with the water sensor. In order to independently cope with the breakdown, you will need to disassemble the device case. For this purpose, you must first remove the back panel of the washing machine. Next, you can see the drain pump at the top. Directly behind it is the water level sensor.

In order to remove the drain pump, you need to use a screwdriver. After that, you should carefully inspect the sensor. If the tube shows defects, it is replaced. In some cases, it can simply fall out of the block. In this situation, it must be fixed there. When the unit breaks down, the sensor must be completely replaced. You can buy it at the service center, informing the model of the washing machine.

Power errors

When the mains voltage is too high, the display will show “9E1”. In order to fix such error codes of the Samsung washing machine, you need to check the current in the network. This operation can be done using a tester. This device is applied to all power contacts. During the operation of the washing machine, it is also necessary to monitor the readings of the tester.

In some cases, the malfunction may be caused by using an extension cord. If its length exceeds 1 meter, then voltage reduction is possible. The most unpleasant thing is the breakdown of the control unit. In such a situation, the voltage is normal, but the washing machine does not see it. This problem is solved by replacing the control module. However, with the code “9E1” this happens very rarely.

Washing machine code “UE

When the Samsung washing machine is broken, the UE error signals the owner about imbalance problems. This indicates that the laundry is unevenly placed in the device. As a result, the drum is skewed. In such a situation, the engine is not able to gain normal speed.

Washing Machine Samsung Errors How To Fix

This error may well arise due to overload. In order to avoid it, you should pay attention to the parameters of the model. In the instructions for the washing machine, the user can find information about the maximum allowable weight of the laundry that the drum can withstand.

Samsung washing machine error code

Washing machines of the “Samsung” trademark are quite popular. Today they are able to boast of excellent quality. However, if used improperly, the owner model can face certain problems. It should also be understood that the breakdown of the “Samsung” washing machine can occur for reasons beyond the control of the owner.

First of all, water affects the wear of parts. Its rigidity differs in different regions of the country. At the same time, the contamination of the pipeline in the regions can be critical. Additionally, problems at the power plant can lead to damage to the electronic board that is installed in the washing machine.

Error in the washing machine “4E

If the display shows the error “4E”, the Samsung washing machine does not turn on due to a broken valve. This may be due to a foreign object that accidentally touched it. Additionally, the valve contacts may be broken. In this case, its winding is damaged. In order to find out the exact cause of the breakdown, experts advise first of all to check the correct connection of the hoses. In some cases, the supply of hot and cold water may be disrupted.

How to find out the error code?

If we talk about washing machines that have a display, then the error code can be easily recognized by the inscription that appears there. In this case, you should first refer to the instructions that came with the model. In it you can learn in detail about the problem that has arisen, as well as ways to solve it. In some cases, you can fix problems yourself without contacting a service center. However, in any case, you should carefully read the safety rules that are indicated in the instructions, and be sure to de-energize the washing machine before work.

Problems with the tachogenerator

Problems with tachogenerators are fairly common. In some cases, they arise precisely because of contacts. In such a situation, the display shows the code “3E”. If this problem is detected, first of all, a specialist inspects the motor winding. It can be broken by overheating. Additionally, third-party items may cause malfunction.

As an example: an unscrewed bolt can get on the winding. Thus, the contacts are broken and the motor is not able to run normally. If the problem lies in the tachogenerator relay, then users will see the Samsung washing machine errors on the displays. “3E2”. In such a situation, the signal between the contacts will be very weak. You can fix this problem by cleaning the relay. If it is dirty, then the contacts are naturally blocked. Even in the engine tachogenerator, the sensor may break. This rarely happens, but the problem is considered serious. In this case, the displays show errors of the “Samsung” washing machine. “3E3”. To fix this problem, you should check all contacts. The gap between them should not be significant. In this case, the signal from the sensor will pass stably.

What is the reason for the code “5E”?

When the Samsung washing machine stops working, the 5e error tells the user about problems with draining the water. Most often, the malfunction lies precisely in the pump, or rather its impeller. This element is located in the washing machine above the engine. In order to inspect it, you must first remove the protective filter. After that, you can twist the pump and check it. The impeller on it is located at the bottom.

In order to replace it, you need to use a key. If, in the end, the pump turns out to be operational, then the problem clearly lies in the drain hose that the Samsung washing machine has. Error “5E” in this situation may signal that the branch pipe is simply clamped. In the worst situation, it will have to be cleaned or changed. Most often, the drain hose becomes clogged due to objects such as coins and buttons falling into it.

The most common mistakes

Most often, consumers contact service centers due to a breakdown of the water level sensor. This detail in the washing machine is quite capricious. As its name implies, it transmits information about filling the tank with water to the control board. The specified sensor consists of a system unit with contacts, as well as a tube. In some cases, only the hose is damaged. It can either detach from the unit or tear as a result of mechanical damage. In any case, the error code “1E” can be seen on the display of the washing machine.

The second common problem is considered to be malfunctions with the electric motor. The device is quite complex and its overload always ends in failure. They occur, for example, when the owner loads too much laundry into the drum. Also, the engine can be blocked if an object has hit it. In this case, the display shows the code “3E”.

Error UE, UB, E4 in Samsung washing machine

The Samsung washing machine normally started the wash cycle, but as soon as it came to spin, it gave an error UE, UB, E4. This means that you have loaded too many or, on the contrary, few things into the drum.

READ  How To Connect The Washing Machine To The Sewer Yourself

To understand how to fix it, you need to understand all the reasons for the appearance of the code.

What does the UE code mean

The Samsung Washing machine UE error appears on the display when the drum is unbalanced. The code E4 is similar to it, which is typical for washers until 2007.

Typically, the washer shows the UE error on the display at the third, seventh or ninth minute of spin. But the washing machine can give an error even after another time after the process of spinning the laundry has begun.

Why the error occurs

When the UE error is displayed on the display, the reason is:

  • Loading too much laundry into the drum;
  • Underload of linen;
  • Washing clothes made of different fabrics that have different weights when wet, which leads to excessive load on the drum during the spin process;
  • Loading too small items into the drum at the same time as large ones, which leads to a strong twisting of the laundry and causes an imbalance in the drum;
  • One-time failure in the control module;
  • Placing your Samsung washing machine on an uneven surface.

It is necessary to determine the true cause of the E4 error in order to know what to do to fix the problem and how to remove it.

How to fix the problem

To make the washing machine work normally again, try to solve the problem yourself first. What to do if the display shows UB error? Follow these steps:

  • If the laundry is out of balance, open the door of the washing machine and manually distribute the laundry evenly.
  • If the drum is overloaded, open the door, take out some of the items and put it back on the spin.
  • If the drum is underloaded with linen, you can moisten a couple of towels with water, wring out a little, open the machine door and put wet towels in the drum. Then start spinning the laundry again.
  • In case of a temporary failure in the control module, you must turn off the machine, unplug the power cord, wait a few minutes, and then restart the washing machine.
  • When tilting the washing machine, level it horizontally so that the distribution of the laundry is even.

To eliminate fault codes E4, UE, UB with a locked door, an emergency drainage of water through a special filter located at the bottom of the washing machine may be required.

If the above methods did not help, and after the test run the washing machine again shows the UE error, then the matter may be in a serious breakdown. you will need to call the wizard, who knows well how to fix the situation.

When you need to call the master for repair

Resetting an error from the display of a Samsung typewriter requires calling the wizard if:

  • There was an error UE on the scoreboard, and the drum does not wring out and rotates only in one direction. The point is a malfunction of the control board. it is possible that the relay on the board or the processor of the control module is out of order. Board replacement required.
  • The drum of the washing machine does not rotate, and the washing machine issues the UE code after starting. it means that the drive belt is torn or stretched. It needs to be replaced.
  • When spinning up to spin, the washing machine rattles heavily, but does not spin. Perhaps a bearing has collapsed or the seal is broken. These elements must be replaced with new ones.
  • The washing machine “speaks” about an error when washing, rinsing or spinning. The reason is the breakdown of the tacho sensor, which requires replacement.
  • The drum of the washing machine can be easily scrolled by hand, but does not wring out on the selected program. This indicates wear on the motor brushes. they need to be replaced.

After finding out the reason for the appearance of the UE code, it is easier to remove the error and correct the operation of the washer. But for this, it is often necessary to invite a specialist who will fix the malfunction.

What to do if the control module fails

To test this option, disconnect the equipment from the network for a few minutes and reconnect it. If the reason is a malfunction of the washing machine controller, after a forced restart, the malfunction signal will disappear.

If the washing machine still shows an error on the display, go to the next diagnostic point.

No contact with pressure switch or electronic module

In case of incomplete contact with the electronics of the unit, the relay that determines the water level does not work correctly and knocks out the E7 error. Check if the electronic units of the washing machine are firmly attached.

If, after checks, the problems persist and the technician re-issues an error, the hardware is probably faulty.

Error E7, 1E, 1C in a Samsung washing machine

For the first time, errors with codes 1C, E7 and 1E can be displayed at any stage of the wash. When the vehicle is restarted, malfunction signals appear immediately after the start, even before water is collected. They talk about pressostat malfunctions.

In washing machines without a display, the E7 corresponds to:

  • blinking of all light indicators;
  • illumination of temperature indicators at 40 and 60 degrees;
  • the lamp of the “cold” wash mode is illuminated.

The E7 error in the Samsung washing machine was used until 2007. In later products, error 1E corresponds to the same problem. In some washing machines, a similar problem is encoded under the 1C sign. These trouble codes are completely similar to each other and are caused by the same set of problems.

Ignoring the notifications of malfunctions that are displayed on the screen of the washing machine can lead to serious malfunctions of the equipment. Sometimes it is possible to clear the error and troubleshoot without calling the wizard.

But first, you need to understand what difficulty the washing machine signals and what the code shown by the technique means.

The pressure switch tube is disconnected from the machine or bent

Inspect the hose connecting the pressure chamber to the water level sensor. When operating the washing machine, the tube may be bent or move away from the connector. In this case, the relay cannot correctly measure the volume of water poured into the tank, and issues a malfunction message. the display will show error E7.

Straighten or reconnect the hose and normal operation of your Samsung washing machine will resume.

What broke

Errors E7 (1C or IE) signal a problem with the water level sensor (it is also a pressure switch). In most cases, this means the need to repair or replace a part.

There are also “false” alarms when a malfunction can be eliminated without the involvement of a master. Let’s figure out what the E7 error and its analogues mean.

How to fix serious problems

Errors 1E, 1C or e7 are most often caused by the failure of some elements. The table will help you figure out how to fix faults.

Check the tightness of the connection of the drain hose with the outlet of the washing machine, eliminate kinks. Make sure the hose is intact.

A specialist is required for an accurate diagnosis. If the resistor in the module is burned out, it is enough to re-solder it.

If you cannot reset the errors yourself, E7 is still lit on the screen and you do not know how to fix the problem. it is better to entrust the repair to the master.

Attempting to troubleshoot a malfunctioning electronic system by a layman may result in a more complex (and more expensive) repair.

Failure of the drain system

What to do if the display shows code 5E or E2? In models without a display, the machine signals by flashing all wash modes and backlit temperature indicator 40 ° C. An error indicates a problem with the water drain.

READ  Add Soda To The Washing Machine When Washing

The reasons for the appearance of the code can be as follows:

  • The hose through which the machine drains water is clogged or kinked. After cleaning or returning the hose to its normal position, the normal operation of the unit is restored.
  • The drain filter is clogged. To check the version, it must be removed, cleaned, rinsed and screwed back.
  • The siphon located at the place where the machine is connected to the sewer is clogged. To eliminate this problem, you need to disconnect the drain hose from the connection to the drain pipe, immerse it in a container, start the program and wait for the water to drain. If it flows freely, you need to urgently clean the siphon.

The machine can issue such an error if the contacts of the drain pump come off. After they are tightly connected, the code does not appear on the screen.

A one-time system crash can also cause an error demo. To check this, you need to turn off the device and turn it on again after 10-15 minutes.

Symptoms of basic problems

Elementary diagnostics can be carried out by the presence of previously unobserved deviations in the operation of the machine or changes in its appearance.

Samsung washing machine errors: how to understand the malfunction and repair

So that the owner can independently find out the errors of the Samsung washing machine, the manufacturer has created a signal system. In the event of a malfunction, the display shows a specific code consisting of letters and numbers.

On those devices where there is no monitor, the corresponding indicators at the buttons on the display light up. Knowing the decoding of the code, you can eliminate a minor breakdown without resorting to the help of professionals. Let’s take a closer look at what the main error codes signal.

Display abnormalities

Symbols freeze and no backlighting. this may indicate moisture penetration into the control panel. Unplug the machine and dry it for 24 hours. If the display does not light up when turned on or unknown characters appear on it, you need to contact the service center.

Various manifestations of water leakage

The presence of a puddle flowing out from under the body indicates flaws in the hoses designed for draining and supplying water. If, upon self-examination, cracks and holes are indeed found, then the elements should be replaced. Otherwise, specialist intervention will be required.

Leaks can also occur if the powder loading compartment is overfilled or clogged. To fix the problem, clean the compartment well.

If the inspection reveals a leak from the places where the pipes are connected to the machine, you must repeat the assembly or replace the seal part.

Possible errors and how to fix them

If a combination of numbers and letters appears on the display of the washing unit, or for models without a screen, a combination of lights is displayed, after which the machine stops working, this means that certain problems have occurred.

Knowing the decoding of the codes, you can quickly navigate the severity of the problem and decide whether this is a consequence of the user’s carelessness or a serious breakdown that requires the intervention of professionals.

Changing body color

The paint can flake off and change color when the washing machine is installed in a damp room. Usually the lower part of the unit body and its bottom are affected.

If the damage is minor, then you can tint and clean the changes yourself. To further correct the problem, you need to reinstall the machine in a dry, well-ventilated room.

One-time malfunction of the machine

How to fix error AE, AC, 13E? The listed error codes appear in the event of an interruption in communication between control boards, the function of which is to receive information from multiple sensors, process it and issue a command to the executing mechanisms.

The error can be corrected by disconnecting the device from the network. If it was a one-time failure. after restarting the machine will work normally.

In the case when after shutdown the code is displayed again on the screen, you need to call the wizard for an accurate diagnosis.

Wrong preparation for washing

How to react to combinations of DE, DE1, DE2, DC, DC1, DC2, ED? Units without screens react to an error by flashing all washing modes and temperatures. The presented combination means that the door is not closed.

It is easy to eliminate the error. you should check the condition of the machine door. Perhaps a piece of thread entangled in the hook or a lock is interfering with the mechanism. Perhaps one of the door parts is bent.

What to do. H1, H2, HE, HE1, HE2, HC, HC1, HC2, E5, E6 appeared? On the machine panel, where the display is not provided, the wash indicators, as well as the second from the top and the lowest temperature indicators, turn on. It should be noted that when working without heating, the error does not appear.

There are two main reasons for the error:

  • The unit is not correctly connected to the mains.
  • Tubular Heater is not working.

If you try to correct the situation yourself, you should check the correct connection of the unit to the mains. In the case of using an extension cord, it is better to replace it with a new one or connect directly.

If, as a result of the actions performed, the machine again indicates a problem, you should contact a professional.

What does the appearance of a combination of LE, LC, E9 mean? Machines without a screen signalize malfunctions with lighted wash buttons and temperature indicators located at the very bottom and top.

This error occurs on the screen when water leaks from the unit. There are several known reasons for its appearance:

  • The drain hose is below the prescribed level.
  • It is not properly connected to the sewer system.
  • Water leaks through the hole or crack in the tank.

In order to troubleshoot problems, follow these steps:

  • Disconnect the unit from the mains.
  • Check the position of the drain hose. Normally, he should first go up, and then go down.
  • Check if the drain filter is open. It can also leak.
  • Disconnect the drainage hose from the drain and put its end in a sink or other container.

Then the machine should be restarted. If everything went well. the reason is eliminated.

What does UE, UB, E4 appear on the display? On the control panel without a display, in this case, the flashing of all wash modes and the temperature indicator of the second one from the top are noted. The combination indicates the difficulty of the machine in distributing the laundry evenly before spinning.

To fix the situation, you need to do the following:

  • Drain the water from the tank.
  • Disconnect the machine from the mains.
  • After waiting 15 minutes, open the door.
  • Having untangled the laundry that has gotten lost in a heap, distribute it evenly over the tank.
  • Close the door and start further program execution.

In some cases, after the performed manipulations, the machine continues to work normally.

Possible breakdowns and ways to eliminate them

If a combination of numbers and letters appears on the display of the washing unit, or for models without a screen, a combination of lights is displayed, after which the machine stops working, this means that certain problems have occurred.

Knowing the decoding of the codes, you can quickly navigate the severity of the problem and decide whether this is a consequence of the user’s carelessness or a serious breakdown that requires the intervention of professionals.

The screen shows tE, Ec, tc

If the machine is not equipped with a display, in case of an identical malfunction on the control panel of the Samsung washing machine, all washing modes and temperature indicators “Bio 60 ° C” and “60 ° C”.

An error indicates a problem with the thermal sensor. responsible for measuring the temperature of the water in the unit.

You can eliminate the breakdown on your own using overload. If this action does not bring any results, you need to contact the service center. Most likely, you will need to replace the sensor or the Tubular Heater.

READ  Washing Machine Samsung Error De Which Means

What does the appearance of a combination of LE, LC, E9 mean

Machines without a screen signalize malfunctions with lighted wash buttons and temperature indicators located at the very bottom and top.

This error occurs on the screen when water leaks from the unit. There are several known reasons for its appearance:

  • The drain hose is below the prescribed level.
  • It is not properly connected to the sewer system.
  • Water leaks through the hole or crack in the tank.

In order to troubleshoot problems, follow these steps:

  • Disconnect the unit from the mains.
  • Check the position of the drain hose. Normally, he should first go up, and then go down.
  • Check if the drain filter is open. It can also leak.
  • Disconnect the drainage hose from the drain and put the end in a sink or other container.

Then the machine should be restarted. If everything went well. the reason is eliminated.

How to decipher errors 4E, 4C or E1

If, during washing or rinsing, the machine has stopped executing the program, and the indicated blinking combinations appear on the display, this is a message about the termination of the flow of water into the drum with laundry. On models without a screen, in this case, the indicator lamps for washing modes and minimum temperature light up.

There can be several reasons for the error:

  • The water inlet hose is pinched by something.
  • Clogged filter located at the outlet of the same hose.
  • The user simply forgot to open the tap on the water supply.
  • The pressure is too small.
  • There is no cold water in the system.

To accurately determine the cause, restart the program and listen for the sound of pouring water.

Further actions completely depend on the presence or absence of sound:

  • If it is heard, but the machine is standing still and continues to indicate an error, it is possible that the drum is overloaded or things are being washed that absorb almost all the water from the tank.
  • When you can clearly hear that water is coming in, the weight of the laundry corresponds to the norms specified in the instructions and the fabric does not absorb water very much, but the flashing display still indicates an error, you need to check the water pressure. Chances are he’s weak.

If there is no sound of pouring water when the supply tap is open and the pressure in the system is normal, do the following: clean the mesh filter, restart the control unit by unplugging it from the outlet for 15 minutes, then plug the machine into the outlet and restart the same wash cycle.

Causes of Uc, 9C, 9E1, 9E2 errors and their elimination

These numbers and letters can appear at any time during program execution. They mean a lack or excess of the voltage in the network for a few seconds. Essentially, it is a volt control that protects electrical components.

If the error appeared on the screen, and then quickly disappeared, the jump in the network was short-lived. In this case, nothing needs to be done. Prolonged display of the code on the screen can be a signal of problems in the electrical network.

Signal reflections can be caused by:

  • Regular power outages. With such problems, it is worth installing a stabilizer.
  • Failure in the volt control system. In this case, it is enough to restart the program by turning the washing machine off and on.
  • The use of a poor-quality extension cord to connect the unit to the network may also cause an error display. Replacing it will solve the problem.

Very often, a voltage control error is displayed on the display in case of poor-quality wiring, old outlet, etc. After replacing these elements, everything falls into place.

Codes 3E, 3E1, 3E2, 3E3, 3E4, 3C, 3C1, 3C2, 3C3, 3C4, 8E, 8E1, 8C, 8C1, EA

The code may appear on the screen as a result of a tachometer error. This small device is responsible for making the engine a certain number of revolutions. On models without a display, in such cases, the wash modes will flash and the temperature indicators 40 ° C and Bio 60 ° C will light up.

  • An amount of laundry is loaded into the drum, the weight of which exceeds the established norm and the engine simply cannot pull such a load. If the hook is in this, then after removing some of the washed items and restarting the device, the device continues to work normally.
  • Demonstration of the code of the described error in the “S amsung” washing machines may occur due to an accidental failure. To check the option, you need to turn off the machine from the outlet and turn it on again after a couple of minutes.

If the restart was successful, there is no reason to worry.

How to identify the main types of problems

Elementary diagnostics can be carried out by the presence of previously unobserved deviations in the operation of the machine or changes in its appearance.

Intermittent rumble during spinning indicates that the machine is not installed correctly or a foreign object has fallen into the drum or housing. In this case, the unit should be carefully inspected and reinstalled.

Noise during draining can be caused by a skewed sub-surface. To eliminate loud noise, you should install the housing correctly and make sure that the drain pump filter is clean.

If during operation the engine roars strongly or there is a knock. professional advice is needed.

Changing the color of the case. The paint can flake off and change color when the washing machine is installed in a damp room. Usually the lower part of the unit body and its bottom suffer. If the damage is minor, then you can tint and clean the changes yourself. To further correct the problem, you need to reinstall the machine in a dry, well-ventilated room.

Leaks can also occur if the powder loading compartment is overfilled or clogged. To fix the problem, clean the compartment well.

If the inspection reveals a leak from the places where the pipes are connected to the machine, you must repeat the assembly or replace the seal part.

Door malfunction. Jamming indicates a power outage. In this case, to open the door, you need to press and hold the power button in this state for a long time.

If the door does not close, it may be hindered by an excess amount of laundry in the drum or by foreign objects entering the gap.

  • How to identify the main types of problems
  • Possible breakdowns and ways to eliminate them
  • What to do. symbols 1E, E7, 1C appeared on the display
  • Codes 3E, 3E1, 3E2, 3E3, 3E4, 3C, 3C1, 3C2, 3C3, 3C4, 8E, 8E1, 8C, 8C1, EA
  • How to decipher errors 4E, 4C or E1
  • What to do. code 5E or E2
  • Causes of Uc, 9C, 9E1, 9E2 errors and their elimination
  • How to fix error AE, AC, 13E
  • What do codes 6E, Eb, bE, bE1, bE2, bE3 say?
  • What do the errors CE, AC, 4C2 mean?
  • How to react to combinations of DE, DE1, DE2, DC, DC1, DC2, ED
  • What to do. H1, H2, HE, HE1, HE2, HC, HC1, HC2, E5, E6 appeared
  • What does the appearance of a combination of LE, LC, E9 mean
  • The screen shows tE, Ec, tc
  • What does the appearance on the display mean UE, UB, E4
  • The machine issues Sud (5ud) or Sd (5d)
  • tips: how to react to washing machine signals
  • How to react to combinations of DE, DE1, DE2, DC, DC1, DC2, ED

    Units without screens react to an error by flashing all washing modes and temperatures. The presented combination means that the door is not closed.

    It is easy to eliminate the error. you should check the condition of the machine door. Perhaps a piece of thread entangled in the hook or a lock is interfering with the mechanism. Perhaps one of the door parts is bent. To restore the operation of the device after inspection, you will need to tightly close the door and restart the program.