Washing Machine Errors Hot Point Ariston

Ariston washing machine malfunctions

Breakdowns among Ariston washing machines are a rare phenomenon, because manufacturers have long established their equipment as the most reliable. But still, even such an excellent technique can fail after a long time of operation. Malfunctions of the Ariston washing machine in most cases are typical and boil down to the replacement of failed elements.

The main malfunctions of Ariston washing machines

Tubular Heater breakage. Thanks to this part, the water is heated to make the washing process more efficient. If a failure occurs for this reason, the machine itself will determine this and issue the corresponding fault code (F03). This can be either a malfunction of the element itself, or the accompanying breakdowns in the power circuit due to the fact that the terminals are burnt out. To eliminate the breakdown, you need to replace the burned out heating element or fix the terminals.

Washing Machine Errors Hot Point Ariston

Bearing breakage. This malfunction is typical for almost all car models of any manufacturer, including the Ariston hotpoint model.

You can see how this is done in or in this article:

Continuous use of the machine causes the bearing shaft to wear out and moisture can get into it. As a result. deformation of the part and incorrect operation of the washing machine.

Faulty pump or filter. Regardless of vertical or horizontal loading, model range, and other indicators, it may happen that the machine refuses to drain or fill water. The reasons may be blockages, burned out pump winding.

Sometimes, in order to get the work done, it is enough to clean the filters, if their further work is impossible, replace them. If everything is normal with the filters, but the water still does not drain, you need to replace the pump.

Most often, you need to tighten the retaining nut or change the rubber seal. Less commonly, manhole cuffs and nozzles can be the culprits. In this case, replace the problem part.

Noise when running the machine with reference bearings. In situations like this, check if the machine is level. If not, you need to align its placement, and a rubber mat can be placed to reduce vibration. If this is done and the car is still noisy, the problem may be with the shock absorbers or the tank strap.

To make repairs, you need to check these parts and, in case of breakdowns, replace the one you need. Another reason for the noise can be small objects that get behind the drum during washing. To eliminate noise, it is enough to take out these small things. Also read this article: https://sovetexpert.ru/prichiny-gromkogo-shuma-v-stiralnoj-mashine.html

Malfunctions of washing machines of other companies:

Washing machine fault codes

Ariston washing machines are equipped with a display that displays information about the washing process, mode. But there is another irreplaceable function of such a display. It will also display the occurred breakdowns under the fault codes. Each such code is responsible for some kind of breakdown and knowledge of their values ​​will help to quickly identify and eliminate the malfunction that has arisen.

The following codes can be displayed on the displays of Ariston Hotpoint or Aqualtis washing machines:

  • F01: indicates a short circuit in the machine’s drive motor. It is necessary to check the contacts of the controller, do not allow moisture to enter the motor. If a breakdown is found, replace the electronic controller or drive motor.
  • F02: the electronic controller has no information about the operation of the motor. Inspection of the motor rotor will help to determine the problem (its operation can be blocked by jammed bearings), and the connections of all parts are also checked. The breakdown can be eliminated by replacing the motor or controller.
  • F03: malfunction of the sensor responsible for the temperature readings, Tubular Heater. To eliminate this code, you need to check if the controller is correctly connected to the temperature sensor, you should see if the sensor has electrical resistance. If all these manipulations did not fix the problem, you need to replace the sensor.
  • F04: breakdown of the sensor that detects the amount of water. Here the problem areas are the sensor itself, with its connection to the controller. If everything is in order, but the code does not disappear. replace the sensor.
  • F05: problems with the drain pump. Check how the controller and pump are connected. If no breakdowns are found, but the problem has not been eliminated, you need to check the pump to see if it has mains voltage. You should also check for blockages in the drain hose. If the breakdown remains after these actions, replace the pump, pressostat.
  • F06: An error occurred with the buttons. It is necessary to check whether the buttons of the device are working, check the panel for the presence of contacts with the controller. The detected breakdown is eliminated, the control panel of the device is often replaced.
  • F07: lights up if the heating element is not immersed in water. Actions: check the quality of the connections between the sensor, which determines the amount of water and the controller, test the sensor itself with the controller, as well as the Tubular Heater. To eliminate the breakdown, you need to replace the problem element.
  • F08: there was a “sticking” relay or problems with the sensor that detects the amount of water. It is worth checking the sensor, relay connections to the controller. If a breakdown is found, the corresponding part is replaced. If no damage is found, change the controller.
  • F09: failure in volatile memory. To eliminate the breakdown, change the controller. You can also try to make the firmware of the microcircuit responsible for the memory of the machine.
  • F10: the sensor for checking the amount of water does not send signals. It is necessary to check the connections, wiring, serviceability of the sensor itself and the controller with the replacement of the used part.
  • F11: no data is received from the drain pump. It is necessary to check the operability of the connector connections from the controller to the pump, test the pump, if necessary, replace it. You should also check the sensor.
  • F12: no communication between the display module and the controller. Similarly with previous breakdowns, the connection is checked, detected breakdowns are replaced with new parts.
  • F13: malfunction of the drying temperature control circuit. It is worth checking the connections of the controller with the dryer, checking the sensor and replacing the inoperative element.
  • F14: during the drying phase, it does not start. It is necessary to check whether the Tubular Heater, which is responsible for drying and the controller, are connected to each other, check the operability of both elements.
  • F15: Drying mode not switched off. Check the connection board, check and then replace the level sensor and the connection board.
  • F17: indicates an open hatch door. Check if there is mains voltage, if the micro-switch of the lock works, how securely it latches. The revealed breakdown is repaired by replacing the lock of the hatch doors.
  • F18: incorrect operation of the microprocessor. To eliminate the code, you need to replace the controller.

Knowing about the fault codes of Ariston Hotpoint washing machines, you can find the reason for the stop. Ariston washers have a complex device, but in many cases it is possible to make repairs with your own hands, while saving time and money.

Repair catalog for washing machines Hotpoint-Ariston (Hotpoint Ariston). Ariston Hot Point Washing Machine Errors

  • |
  • I’m lucky
  • |
  • Price list
  • |

Our company has been repairing all brands of washing machines at home for over 5 years.
We have established ourselves as a reliable and responsible partner.

We work throughout Moscow and the nearest Moscow region,
24 hours a day, 7 days a week, without weekends and holidays.

Hotpoint-Ariston (Hotpoint Ariston) washing machine error codes

Hotpoint-Ariston (Hotpoint Ariston)

Hotpoint-Ariston (Hotpoint Ariston) washing machines malfunctions

In this column you can see what needs to be done to fix the malfunction of the washing machine, but entrust it to the repairmen of washing machines.

Deciphering the code of the Hotpoint-Ariston washing machines (Hotpoint Ariston)

Possible malfunction of the Hotpoint-Ariston washing machine (Hotpoint Ariston)

F 01

A short in the washing machine motor control circuit.

Moisture has got on the contacts of the connector of the electronic controller. remove moisture, service the controller contacts.

The electronic controller is out of order. repair the controller (replace the burned-out ED triac) or replace the entire controller.

There is a short circuit in the rotor winding of the drive motor. replace the electric motor of the Hotpoint-Ariston washing machine (Hotpoint Ariston).

F 02

The signal about the rotation of the electric motor is not received by the electronic controller of the washing machine.

There is a malfunction of the drum bearing unit, which can lead to blocking of the ED rotor. replace the bearings.

An open circuit appears in the controller-electric motor circuit. identify the location of the open, replace the problem wire or seal the contacts.

The tachogenerator is out of order. replace the ED-TAKHO unit.

The electronic controller is out of order. repair the board or completely replace the controller of the Hotpoint-Ariston washing machine (Hotpoint Ariston).

F 03

Malfunction of the water heating system in the washing machine.

There is a loose contact in the devices on the “controller. temperature sensor” circuit section. tighten contacts, replace defective wiring sections.

2. There is a malfunction on the controller board. check and, if necessary, replace the Tubular Heater water heating relay.

3. The temperature sensor has failed. replace the thermistor of the Hotpoint-Ariston washing machine (Hotpoint Ariston).

4. The electronic controller is out of order. replace the burned out parts of the controller board or completely replace the controller of the washing machine completely.

F 04

Malfunction in the water level control system.

If the water level sensor is faulty, repair the hydraulic system of the pressure switch or replace the complete pressure switch assembly of the Hotpoint-Ariston washing machine (Hotpoint Ariston).

There is a loose contact in the devices on the “controller. water level sensor” circuit section. tighten the contacts, replace defective wiring sections.

3. The electronic controller is out of order. replace the burned out parts of the controller board or completely replace the controller of the washing machine completely.

F 05

Malfunction of the water drain system (the “Empty tank” signal is not generated).

An open circuit occurs in the controller-biLGe pump circuit section. tighten the contacts of the devices included in the circuit, if necessary, replace the defective wiring harness.

The biLGe pump is out of order. replace the pump.

Significant dirt has appeared in the pump filter, which prevents the entire system from working normally. clean the pump filter.

There are problems in the drain hose (the hose is dirty or kinked). clean the hose, restore it to its normal position, according to the instruction manual.

The pressure sensor is out of order. repair the sensor’s hydraulic system, if it is impossible to repair. replace the pressure switch.

Electronic controller unit burned out. replace defective parts of the controller board or completely replace the Hotpoint-Ariston electronic controller (Hotpoint Ariston).

F 06

Malfunction in button devices (button does not work). The malfunction is typical for “Ariston Dialogic” (AD series).

There are violations of contacts in the seats of the control panel buttons. they clean the button sockets, if it is impossible to restore normal contact, the button changes or the entire front panel is changed.

2. An open circuit appears in the controller-front panel section. check the reliability of the connections, if necessary, replace the defective wiring harness.

The electronic controller is out of order. the controller board is being repaired, the burned out parts are replaced, if necessary, the entire controller unit of the Hotpoint-Ariston washing machine (Hotpoint Ariston) is changed.

F 07

Malfunction of the Tubular Heater control system (there is no signal about the complete immersion of the Tubular Heater in water).

READ  Washing Machine Samsung Change Bearing Video

There is no contact on the water level controller-sensor circuit. It is necessary to check the circuit connections, seal the connectors, service the contacts.

The water level sensor is out of order. repair the sensor, replace the pressure switch if necessary.

There is a problem with the Tubular Heater. replace the thermal heater.

The electronic controller does not work. repair the controller board, service its contacts, if necessary, replace the controller of the Hotpoint-Ariston washing machine (Hotpoint Ariston).

F 08

Malfunction of the control system Tubular Heaterm (signals “Overflow” and “Empty tank” are simultaneously present).

There is a breakdown of the pressure switch. it is necessary to repair the pressure switch or replace it.

There was an open circuit in the controller-Tubular Heater section. inspect and service its contacts. Replace Tubular Heater if necessary.

Electronic controller faulty. repair the controller board, service its contacts, if necessary. replace the controller of the Hotpoint-Ariston washing machine (Hotpoint Ariston).

F 09

EEPROM memory failure (memory content error).

There was a failure in the electronic controller of the washing machine. it is necessary to replace the controller (if possible, overwrite the memory contents).

F 10

Malfunction of the water drain system (the signal “Full tank” is not generated).

There is no contact on the water level controller-sensor circuit. It is necessary to check the circuit connections, seal the connectors, service the contacts, or replace the defective sections of the wiring.

The water level sensor is out of order. repair the sensor’s hydraulic system, if it is impossible to repair, replace the washing machine pressure switch.

There is a malfunction of the electronic controller. replace the defective parts of the controller board or completely replace the Hotpoint-Ariston electronic controller (Hotpoint Ariston).

F 11

Malfunction of the biLGe pump (there is no signal about the operation of the pump).

There is no contact on the controller-biLGe pump circuit section. It is necessary to check the circuit connections, seal the connectors, service the controller contacts or replace the faulty wiring sections.

The biLGe pump is broken. replace the Hotpoint-Ariston pump (Hotpoint Ariston).

The electronic controller is out of order. the controller board is being repaired, the burnt parts are replaced, if necessary, the entire controller unit of the washing machine is changed.

F 12

Faulty display of the front panel (mode indicators do not light, message screen does not work).

There is no good seal in the contacts of the display module. service the contacts, check the wiring section from the controller to the display module, if necessary, eliminate defects in the wires.

The electronic controller is out of order. the controller board is being repaired, its terminal block is serviced, burned out parts are replaced, if necessary, the entire controller unit of the Hotpoint-Ariston washing machine (Hotpoint Ariston) is changed.

F 13

Drying temperature control system malfunction (for washing machines with dryers).

There is no contact on the controller-biLGe pump circuit section. It is necessary to check the circuit connections, seal the connectors, service the controller contacts or replace the faulty wiring sections.

There is a breakdown of the thermostat. check and service the contacts or replace the thermistor.

The electronic controller is out of order. the controller board is being repaired, its terminal block is serviced, burned out parts are replaced, if necessary, the entire controller unit of the Hotpoint-Ariston washing machine (Hotpoint Ariston) is changed.

F 14

Washer dryer system malfunction (for washer dryer). Drying does not start.

There is no contact on the controller-Tubular Heater drying circuit. It is necessary to check the circuit connections, seal the connectors, service the controller contacts, or replace the faulty wiring sections.

Deteriorated Drying Tubular Heater. Replace Drying Tubular Heater.

The electronic controller is out of order. the controller board is being repaired, its terminal block is serviced, burned out parts are replaced, if necessary, the entire controller unit of the Hotpoint-Ariston washing machine (Hotpoint Ariston) is changed.

F 15

Washer dryer system malfunction (for washer dryer). Drying does not turn off.

There are no tight contacts on the drying connection board. service the contacts, replace the board if necessary.

There is a malfunction in the water level sensor in the dryer. check and service the sensor contacts, if necessary. replace the sensor of the Hotpoint-Ariston washing machine (Hotpoint Ariston).

F 17

Malfunction of the door locking system (for washing machines with the Easy Dorr function).

A defect has appeared in the mechanical part of the hatch door latch. repair the UBL latch, replace it if necessary.

There is no reliable contact in the microswitch of the door lock. clean and seal the contacts or completely replace the door lock.

There is a malfunction on the controller board. replace the defective parts, or replace the entire controller of the Hotpoint-Ariston washing machine (Hotpoint Ariston).

F 17

Malfunction of the door locking system (for washing machines without Easy Dorr function).

A defect has appeared in the mechanical part of the hatch door latch. repair the UBL latch, replace it if necessary.

There is no reliable contact in the microswitch of the door lock. clean and seal the contacts or completely replace the door lock.

There is a malfunction on the controller board. replace the parts that are out of order, or replace the entire controller of the Hotpoint-Ariston washing machine (Hotpoint Ariston).

F 18

There is a malfunction in the microprocessor.

There is no reliable contact on the connection board of the electronic controller. clean and seal the controller contacts.

The electronic controller unit is out of order. replace the damaged parts, or completely replace the controller unit of the Hotpoint-Ariston washing machine (Hotpoint Ariston).

Repair of washing machines Hotpoint-Ariston (Hotpoint Ariston)

The Hotpoint-Ariston Aqualtis AQSL 109 automatic washing machine, purchased about five years ago, has never broken down during its entire operation, although it worked quite intensively. However, recently, during its operation, the user drew attention to extraneous noises coming from the inside of the device. They are especially audible during spinning when the drum is rotating at high speed. In general, there are no complaints about the quality of washing, all programs are running correctly. The display panel does not display a failure or error message.

The Hotpoint-Ariston AQSL 057 U washing machine was not working during the last start-up. After the user selected the mode and started the device in operation, the filling and heating of water in the tank occurred normally, but after that the drum did not rotate, although the engine was running, which could be heard from the characteristic sounds from inside the case. After a short run of the engine, the machine turned off and showed a malfunction on the display panel. Repeated launches did not lead to anything. The equipment was purchased seven years ago, until that time it worked properly all the time of operation.

After the washing program has been completed, including spinning the washed laundry, the Hotpoint-Ariston AVTL 109 automatic washing machine does not stop, but starts the whole cycle again. This continues several times on any selected program, so the user has to wait for the spin and stop the machine manually. The quality of the wash is good, the laundry comes out clean. The device is eight years old, it worked properly all the time after purchase.

During the Wool wash program, the Hotpoint-Ariston ARTL 83 EU automatic washing machine stopped in the middle of the rinsing phase. The user sensed a burning smell coming from the inside of the device. When the machine is connected to the network, it shows the presence of voltage, the “Network” button is lit on the panel, but it is impossible to select any program and start the machine. The equipment was purchased six years ago, there were no breakdowns before.

After intensive use for five years, the Hotpoint-Ariston AVTF 109 automatic washing machine does not drain the water from the tank. The main wash cycle ends with the appliance blocking, leaving dirty water in the tub. In this case, an error message appears on the control panel in the program operation. The machine is idle for a while in standby mode and then turns off. The user has to perform manual draining. The same happens when setting the rinse as a separate mode.

After selecting a program, the Hotpoint-Ariston AQSL 097 washing machine does not turn on, water does not start flowing into the tank. the user, after pressing the start button, does not hear the sound of the automatic hatch locking device. The malfunction is typical for all programs, so it is impossible to start the machine, washing cannot be carried out. The device was purchased five years ago, until this moment it has not been repaired.

The Hotpoint-Ariston Aqualtis AQSL 109 washing machine has recently noticeably increased the time it takes to complete the main cycle for any selected wash program. The machine works at this stage for about one and a half times longer, but no information about an error or malfunction is sent to the control panel of the machine. The washing quality has not deteriorated, but the use of the device has become inconvenient due to the increased operating time. The equipment was purchased six years ago, and worked without breakdowns during the entire operation.

Recently, the Hotpoint-Ariston ARUSF 105 washing machine, after starting on any washing program, collects an excess volume of water into the tank. This interferes with washing, since it is rather difficult to select the concentration of the powder. In addition, in this case, the specified technological requirements are violated. The device does not show any irregularities in the execution of the program, the indicators are not illuminated. The equipment was purchased five years ago, until that time there were no violations in its operation.

On some selected programs, the Hotpoint-Ariston ARSL 109 washing machine does not heat the water to the required temperature. This is usually typical for such washing modes where a high temperature is required, more than 50 degrees. in this case, the machine does not start washing, displaying an error message on the display panel, and then turning off and going into standby mode. it is inconvenient to use the equipment. the device was purchased six years ago, before that it was not given for repair.

During the operation of the Hotpoint-Ariston ARTXF 109 washing machine, serious defects began to appear from time to time, which are expressed in strong vibration of the device body. during spinning, this malfunction appears constantly, the apparatus vibrates to such an extent that it begins to move along the floor, moving from its place. The quality of washing has not deteriorated, but the user is afraid of more serious malfunctions and malfunctions, so he temporarily stopped turning on the machine. The device was bought four years ago, it has not been repaired before.

After the last wash with a full drum load, the Hotpoint-Ariston AQSL 057 U washing machine stopped turning on. The power indicator is on when the plug is connected, but the machine does not allow you to select a washing program. The indicator panel does not signal a malfunction in any way; when you try to rearrange the modes on the panel, the LEDs do not light up. The equipment was purchased six years ago, it worked properly all the time of operation, it was never returned for repair.

Recently, the Hotpoint-Ariston ARUSL 105 L washing machine has been problematic to drain water. At any stage of washing, both during the main cycle and during rinsing, after the end of the cycle, draining is very slow and not completely. The user hears the biLGe pump running, but after a few minutes it stops and a failure message is displayed on the display panel. We have to make a forced drain of water from the tank. The equipment was purchased five years ago, never broke before.

The Hotpoint-Ariston AVTL 109 (EU) automatic washing machine stopped turning on the washing after several power surges. After starting the selected program, the water filling is turned on, but then the device stops and goes into standby. Heating does not occur. The malfunction is typical for any mode, therefore it is not possible to wash in a typewriter. The equipment was purchased four years ago, until that time there were no breakdowns.

During the last few washes, the Hotpoint-Ariston AQSD 129 automatic machine stopped developing high drum speeds during the spin cycle. The spin quality is unsatisfactory, the user has to manually squeeze the clothes. The device does not respond to a malfunction, there is no information on the malfunction on the panel. The machine was purchased five years ago, until this moment there were no problems with the operation of the equipment.

READ  Washing Machine Does Not Heat Water But Works

For several washes in a row, the Hotpoint-Ariston ARTF 1047 automatic machine malfunctions, after selecting the necessary mode, the device sometimes simply cannot be started. In case of such failures, an error is displayed on the control panel, after a few seconds the machine goes into sleep mode. The machine was bought from hands three years ago, during operation it proved to be good, never broke.

The Hotpoint-Ariston AVTL 104 automatic washing machine has recently been washing without heating the water in the tank. In this case, the apparatus works as if there was no failure, the drum rotates, all program cycles are executed to the end. As a result, at the exit, the user receives poorly washed clothes. The device was purchased six years ago, until that time it has never broken.

During operation, the Hotpoint-Ariston AVTF 129 washing machine has recently begun to hum and make extraneous unpleasant sounds. There are no failures during operation, the device does not display error or failure messages on the control panel. However, it becomes dangerous to use the technique, since there is a possibility of a defect developing. The car was purchased seven years ago, until that moment they actively used the technique, but there were never any problems.

Recently, the Hotpoint-Ariston ARUSL 105 L automatic washing machine does not work when spinning the washed laundry. The drum stops constantly after a short rotation, there is no reverse, the rotation speed is low. After each stop of the drum, the device displays an error on the panel, the user has to restart the program. The spin cycle never goes through without stopping. The equipment was purchased four years ago, there have never been any breakdowns before.

The Hotpoint-Ariston ARUSF 105 automatic washing machine has been in operation after purchase for more than four years, and is actively used all the time. Until recently, there were no problems in operation, however, over the past few washes, the owner of the equipment noticed that the water in the tank does not heat up to the set temperature, which is noticeable by the heating of the hatch glass. Washing on such modes as “Linen” and “Cotton” takes place at a water temperature not higher than 40 degrees, which qualitatively affects the washing results. The device does not display error information on the display panel while operating these programs.

During the last wash, the Hotpoint-Ariston ARSL 109 automatic machine suddenly stood up, gave a failure on the control panel and turned off spontaneously. After that, the client felt a burning smell, as if the wiring was burnt. Re-enabling the equipment was unsuccessful, the machine does not start. Only the network indicator is lit on the panel, but no programs are selected. Further use of the technique is impossible. The machine was purchased six years ago, has never been repaired, has not given out any malfunctions.

The last wash in the Hotpoint-Ariston AVTL 109 washing machine took almost an hour longer than it should have been in the program. After that, the user started the device several more times, but the machine always poured water for a long time, and heated it much longer than usual. At the same time, the control panel of the car does not display anything, information about failures does not appear. The equipment was purchased five years ago, before this problem occurred, the machine never broke down.

Recently, the Hotpoint-Ariston ARSF 100 L washing machine at the main stages of washing began to make spontaneous short-term stops of the drum. During the entire cycle, the machine can stop several times, several LEDs are on on the indicator panel at this time. After one or two minutes, the machine starts up again, the indicators go out. This problem has never happened before. The car was bought six years ago, there was never a repair.

The Hotpoint-Ariston AVTL 109 (EV) HA washing machine began to experience malfunctions. This results in the machine stopping at the main program in the main cycle. The machine cannot go to rinse after the main step. The equipment is blocked, the control panel indicates a malfunction. You cannot wash in any mode. The car was bought five years ago, it has never broken before.

During the operation of the Hotpoint-Ariston AQSL 857 U washing machine, a puddle of water appears below the body, which must be constantly removed. At the same time, the machine does not react to a leak, it works as usual. The malfunction develops with each wash, the puddle gets bigger. This does not affect the quality of washing yet. The equipment was purchased seven years ago, until that time there was no repair.

The Hotpoint-Ariston ARSF 100 automatic washing machine, after starting the program, draws more water into the tank than the set level. This malfunction appears constantly, in any selected mode and during rinsing. As a result, washing is less efficient, since the concentration of the powder is less. It became inconvenient to use the equipment. The device was purchased seven years ago, before this problem occurred, there were never any faults.

Ariston or Hotpoint-Ariston washing machine. error code F05 / F5

The washing process started normally, but after a while you found that the Ariston or Hotpoint-Ariston washing machine stopped full of water and writes the F 05 / F 5 code on the display. Before the F05 error lit up, strange sounds might be heard:

  • strong hum (drain pump);
  • a crackling sound similar to the sound of an object hitting a spinning fan propeller.

Attempts to turn on the drain program forcibly do not lead to success: the Ariston machine again gives the same error, and the water does not drain.

For the first time, error F 05, most often, occurs during a wash or rinse cycle, less often during a spin cycle. On subsequent launches of the washing program (if you managed to drain the water manually), you will see this error on the wash cycle.

In rare cases:

  • the Ariston machine can drain the water, and then give an error F05 / F5 (on washing, rinsing or spinning);
  • code F 05 / F 5 can be displayed immediately after pressing the button to start washing (“Start” / “Start”).

If you have a washing machine without a screen, then Ariston will report error F 5 / F 05 using the indicators:

  • On the oldest models made by Ariston Margherita, you will see a fast blinking on / off indicator. It will give out a series of flashes, a kind of light morse code from five points. Then a long break will follow, after which 5 flashes of the indicator will repeat. In this case, the door lock indicator (“Key” or “Lock”) will light up, and the program selection knob can click and rotate in a circle.
  • On more modern Washing machines Ariston without display (AVL, AML, AVSL, etc.), the F05 error message will be displayed in a combination of constantly flashing Superwash and Extra Rinse buttons (first and third from the bottom). Their blinking will be accompanied by more frequent blinking of the “Key” indicator of the door lock
  • The Hotpoint-Ariston washing machine of the Low-End line (models ARSL, ARXL, etc.) will show error F05 by a combination of flashing indicators “Key” and “Drain” (the first and third lamps in the vertical row of indicators of the program execution phases). Also, all buttons of additional functions (horizontal row of indicators) may be constantly lit.
  • Hotpoint-Ariston Aqualtis models without a screen will flash temperature indicators of 40 ° C and wash in cold water (first and third temperature lamps).

Error F 05. what to do, and in what cases you can fix it yourself

  • Control failure. Washing machine electronics are sometimes wrong. And the drain error message appears by accident. The Washing machine must be restarted to resolve the failure. To do this, turn off the machine with the power button and unplug the plug for 5 minutes. Then plug it back in and press the on / off button. If the error was false, the F 05 code will no longer appear.
  • Clogged filter. Often the water is not drained due to debris trapped in the drain filter of the Ariston washing machine. Animal wool, threads from clothes, garbage from s gradually accumulate and clog the lumen, so the water stops passing.
    For normal operation of the washing machine, the blockage must be removed. To do this, first drain the water from the drum by hand, for example, through the emergency drain hose or in any other way described in the article “How to drain water from the washing machine if it breaks down”. Then open the small hatch (usually found at the bottom of the machine in the front right corner), unscrew the drain filter and remove the debris. Before unscrewing the filter, place a floor cloth under the washer so as not to flood the floor with residual water. After cleaning, carefully screw the filter back in and start washing. If error F05 has disappeared, then the cause has been eliminated.
  • The drain hose is blocked. Sometimes lumps of debris will slip through the pump into the drain hose and block the water drain. To solve the problem, similar to the previous point, first drain the water from the tank by hand. Then disconnect the hose from the washing machine and drain. Then find the plug, knead it and rinse the hose under a strong stream of water to remove the blockage. Reconnect the hose, start any wash program, wait for the Hotpoint Ariston washing machine to draw water, then forcibly turn on the spin program. If the error does not appear, but the machine drained the water and wrung out the laundry, then the cause of its occurrence has been eliminated.
  • Sewer blockage. A clogged siphon or sewer pipe is a common cause of the F5 error on the Washing machine Ariston, if the drain is organized directly into the sewer, and not into a bathtub or toilet. Diagnosing a problem is easy! Pull the opposite end of the hose out of the drain, lower it into a bathtub, toilet or bucket and forcibly start the spin program. If the error disappears, and the machine drains the water and starts to wring out the laundry, then your sewer is clogged. You can clean it with a cable and special tools, and the siphon must be disassembled and washed.

Also refer to the “Troubleshooting” section in the instructions for your Hotpoint-Ariston washing machine. It lists common problems that you can deal with on your own. If these recommendations do not help, and error F 05 still interferes with the operation of the Ariston washing machine. call a specialist for professional repair.

Decoding the error

F5 / F05 code in Ariston or Hotpoint-Ariston washing machines means a drain error. For some reason, water does not drain or the level sensor (pressure switch) erroneously gives incorrect information about its presence in the drum, instead of the message “Empty tank”.

The appearance of the F5 error in the Washing machine Hotpoint-Ariston is quite common. Fortunately, in almost half of the cases, according to the statistics of the workshop “”, you can handle it yourself.

Probable faults requiring repair

Since 2003, RemTytTech has been troubleshooting Ariston and Hotpoint Ariston washing machines. 5878 washing machines passed through the hands of the masters! The table contains typical breakdowns that cause the F 05 / F 5 drain error on the Washing machine Ariston.

In older cars, the main reason for pump failure is the development of the watch resource. New. small objects getting into the pump.

A module with a failed processor cannot be repaired, it needs to be replaced.

In other cases, most often, repairs cost. It is necessary to repair the damage on the board (restore tracks, replace radio components). If the firmware fails, you need to reflash the electronic controller. If repair attempts are unsuccessful, it is necessary to completely replace the Control Unit.

Washing machine Ariston:

Pressure switch defective. Due to a breakdown, the water level sensor does not generate a signal about an empty tank. It still seems to him that there is water in the drum, although the machine has drained the water.

Washing machine Ariston:

  • stopped for washing, rinsing or spinning;
  • randomly turns on the drain;

Problems with the power supply of the nodes. There is no supply voltage on the pressure switch or drain pump, or there is a signal interruption between these nodes and the control board.

The reasons may be:

The price is only for work, spare parts are paid additionally. The final price will be known after the technician diagnoses the equipment on site.

READ  How To Change The Bearing On A Washing Machine Ariston

Washing instructions:

  • Press the button to turn on the washing machine. It is located on the front panel.
  • We load dirty laundry. Before that, it must be sorted, the s of all clothes must be checked. The weight must not exceed the permissible.
  • Pour the detergent into the special holes.
  • Close the hatch.
  • If you need to change the program or enable additional functions, then at this stage you need to click on the corresponding buttons.
  • Press the “Start” button. The wash has started.
  • After a certain time, which is shown on the display, the wash will end. you can open the hatch in a couple of minutes and take out your clothes.

Ariston washing machine programs

Washing machine “Ariston”, the instructions for which are available in the unit itself and on the manufacturer’s website, has many programs and functions that are designed for different types of laundry.

All Hotpoint-Ariston washing machines are equipped with the following programs:

  • removing serious stains;
  • pre-wash cotton;
  • program for cottons made from durable fabrics;
  • washing of cotton linen, consisting of delicate fibers;
  • washing heavily soiled synthetics;
  • program for lightly soiled synthetic products;
  • quick wash function at 60 degrees of water;
  • a daily program designed for a small load. the water temperature is 30 degrees;
  • function “my program”;
  • wool;
  • program for cleaning bed linen.

Important! The “my program” function allows the consumer to create his own personal program, while setting all the modes that are necessary. You can use it anytime you want.

Additionally, there are functions of rinsing, draining water and spinning.

All Ariston washing machines, instructions for which are present in all units, are very popular. This is due to the fact that there are programs that allow you to save water and electricity. So, in the modes “bed linen”, “stain removal”, “wool”, automatic weighing takes place, calculation of water, which are necessary for washing this linen.

When buying this unit, you save the resources of your country, and your utility bills are decreasing exponentially.

Important! Where do you plan to install a washing machine? We have prepared separate posts where we have collected tips from the best designers:

History of the company

Hotpoint-Ariston is the result of the merger of the two brands Hotpoint and Ariston. Before they came together, they were popular manufacturers who only made quality units at reasonable prices. The most important owner of these companies is the director of the Indesit brand, which also includes other small brands.

Important! Due to the unification of the Italian and British factories by a world-famous concern, for residents of the CIS countries, these household appliances are slightly cheaper. Washing machines are manufactured in the Lipetsk region according to standards and regulations.

The Hotpoint-Ariston brand manufactures all its units according to the wishes of the customers. They always listen to the opinions of their consumers and improve their equipment according to the latest trends. All devices are distinguished by excellent quality, convenience, attractive design, reliability and versatile functionality. It is safe to say about this trade mark that it is time-tested and many customers trust it.

Let’s now talk in more detail about the Hotpoint-Ariston washing machine, its instructions and capabilities. We will also discuss tips and nuances for the care and washing of linen.

Important! On our portal of useful tips there is another special article dedicated to the Ariston washing machine.

Washing machine Ariston. instruction

Washing procedure

In order for the “Ariston” washing machine to serve you as long as possible, you must use it correctly, wash according to specific instructions. It is about her that we will talk in this chapter.

Important! Use special detergents for washing clothes in an automatic washing machine, they will help to extend the service life of the equipment. We talked about these tools in detail in our separate reviews:

Front panel and washing machine programs

The front panel of the Ariston washing machine contains:

  • device power button;
  • knob for setting programs;
  • a button for changing the temperature from the one that is set to a certain function;
  • spinning;
  • delayed start;
  • “options” button;
  • washing start button;
  • pictograms that show at what stage the wash is;
  • hatch lock indicator;
  • child protection.

Important! A ready-made decoding of the icons on the washing machine will help you to understand the functionality and settings of the equipment in more detail.

In addition to the above functions, there is a display on the front panel of the Hotpoint-Ariston washing machine. This part has an image on which certain data are recorded. So, you can see which program you have chosen to wash your laundry, at what stage it is and how much time is left until the end of the program. The image also shows whether the delay start is enabled.

On the display you can see the number of drum revolutions during spinning. As a result of this, you can change the speed, if necessary. It also shows the temperature at which the laundry is washed.

Washing machine care

All washing machines, regardless of brand and manufacturer, require constant care. The better you look after her, the more she will serve you. Let’s take a look at the Hotpoint-Ariston washing machine today. the instructions for caring for it look like this:

  • Periodically wash the outer surfaces, drum and cuff (elastic around the hatch) with a cotton cloth dampened with soapy water.
  • Ariston washing machines are equipped with a self-cleaning program, which must be turned on once every two weeks. The drum must be completely empty.
  • Clean containers for washing powders and gels regularly.
  • Open the window after washing. This is necessary in order for the remaining moisture to erode.
  • Look at the filter every three to four washes. It should be free of dust, dirt, fine litter.

Important! Washing machine care is a guarantee of its long-term operation. In order not to spend a long time looking for the necessary information and choosing the right products, use the ready-made information on the prevention of the washing machine.

  • History of the company
  • Front panel and washing machine programs
  • Washing procedure
  • Ariston washing machine programs
  • Washing machine care
  • material

Washing machines, according to statistics, are the most frequently purchased type of household appliances. Today, all the fair sex cannot do without this wonderful machine, which is independently ready to wash clothes, rinse, dry and even iron. Today we will talk about the Ariston washing machine, the instruction of which allows you to find out all the necessary information about the technique, its operation, the efficiency of the device and its convenience even before buying.

material

Buy a Hotpoint-Ariston washing machine, read the instructions, and it will serve you for a very long time!

Ariston washing machines

Ariston washing machines are known all over the world for their quality, design and implementation of advanced technologies. Some car models are called Hotpoint Ariston, I wonder why? To find out, we propose to study a little the history of the brand, consider all the advantages of cars of this brand, find out what their weaknesses are.

A bit of history

Back in 1930, a company was created in Italy by Aristide Merloni, which successfully began to manufacture scales Industrie Merlon. Since 1945, it has been developing a new production niche for the manufacture of electric water heaters under the Ariston brand (this Greek word translated into Russian means “successful”).

In 1970 Aristide divides his company into 3 parts and transfers the management of them to his sons:

  • Antonio became head of the Antonio Merloni SpA plant for the manufacture of scales and gas cylinders;
  • Vitorio got the company Merloni Elettrodomestici, engaged in the manufacture of home appliances, of which he became president in 1975, from that time on the independent existence of the Ariston brand;
  • Francesco became president of Merloni Termosanitari for the production of water heaters and bathtubs.

The decision was strategically reasonable, and production immediately went up. Representative offices began to appear in other countries: in Poland, Portugal, Turkey, France. In 1990, Merloni buys the French concern Scholtes, and then the English Hotpoint, thus conquering a large sales market in France, Great Britain and Ireland. In 2005, the fame of Indesit forced to rename the Elettrodomestici concern into the Indesit Company concern.

Elettrodomestici dealership appears in 1995. Consumers appreciated the products of the brands Indesit and Ariston.

In 2000, Merloni buys out the Russian plant Stinol in Lipetsk, where he starts production of Indesit equipment. And in 2004 the company builds a second plant. After the merger with Hotpoint, the Ariston brand was to be renamed Hotpoint. In some countries this has happened, but in the CIS countries, since 2007, washing machines have been produced with the double name Hotpoint Ariston.

Thus, the world’s largest concern for the production of equipment Indesit Company owns such well-known brands as Hotpoint, Stinol, Indesit, Ariston. In our country it is a leader, offering equipment in different price segments.

Advantages and disadvantages

  • cost optimization, namely the reduction of energy consumption and water consumption during washing;
  • adjustable software that allows you not only to select the mode, but also to set the temperature and time at your own discretion;
  • ease of management;
  • a variety of models of washing machines, both economy and premium, which is suitable for consumers with different income levels.

You should not hide the shortcomings of cars of this brand, we will list them:

  • one of the weakest points in the Hotpoint Ariston washing machine is the drain pump (pump);
  • also in some models, rather flimsy fastenings of the drum door and top cover;
  • often craftsmen change hoses, especially at the point of connection to the tank of the machine, perhaps this is due to the operating conditions and hard water, which is not a drawback of the machine itself;
  • malfunctions in the control module.

Note! Repair of washing machines is a relatively inexpensive automatic machine of this brand, while there are always spare parts for all models on sale at an affordable price.

Description of models and their characteristics

At the end of the article, we will conduct a small review of Hotpoint Ariston washing machines, compare their technical characteristics, price and design.

Hotpoint Ariston VMSF 6013 B. automatic washing machine with front loading up to 6 kg and spinning up to 1000 rpm. Of the functions, we note autoweighing. The total number of programs is 16, including anti-allergenic wash. The safety system includes child protection, sunroof lock, overflow protection and self-diagnosis of faults. With dimensions of 85x60x40 cm, its weight is 62.5 kg.

Hotpoint Ariston AQ105D 49D EU / B. washing machine with a maximum load of cotton fabrics up to 10 kg, synthetics up to 5 kg, wool up to 2.5 kg. The spin is adjustable up to 1400 rpm. A total of 16 washing modes are programmed, among which there is a mode “Shirts”, “Down jackets”, “Down blankets”, “Refresh”. The disadvantage is the lack of protection against leaks. With dimensions 85x60x65 s, weight is 75.4 kg.

Hotpoint Ariston VMSD 722 ST B. washing machine with the ability to wash up to 7 kg of linen and spin up to 1200 rpm. There are 16 washing programs in total, including the Refresh program, during which the laundry is steamed for 20 minutes, which eliminates unpleasant odors and allergens. There is protection against overflow and overheating, self-diagnosis, there is no protection against leaks. With dimensions of 85x60x44 cm, it weighs 63 kg.

Hotpoint Ariston WMTL 601 L CIS. vertical automatic machine, maximum load weight 6 kg, spin up to 1000 rpm. There is an automatic weighing of laundry and 18 washing programs, among which there are “Mixed laundry”, “Soak”, “Freshen up”, “Cotton Eco”. This vertical machine is assembled in Slovakia. With dimensions of 90x40x60, its weight is 58 kg.

Hotpoint Ariston AWM 108 is a built-in washing machine with a maximum load weight of 7 kg. Spin up to 1000 revolutions. Washing class and energy consumption A. There are all the necessary washing modes, but there is no child protection. With dimensions 60x54x82 and weight is 72 kg.

So, we note that, despite the presence of Indesit Company enterprises, on the domestic market there are models of Hotpoint Ariston automatic washing machines assembled in Italy and Slovakia. Of course, the price of such models is somewhat different from their Russian counterparts, and the quality, according to some experts, is better for foreign automatic machines. But the choice is yours, good luck!