Washing Machine Bosch Does Not Drain Water

Cleaning the nozzle

Anything that passes through the filter mesh enters the pipe. The element goes in conjunction with the pump, so let’s consider how to get to the pump. In most Bosch models, the bottom is removable, but the cross bar prevents access to the parts. So do it like this:

  • Pull out the plug, disconnect the machine from communications.
  • Close the inlet valve.
  • Remove the dispensing tray by pressing the latch in the center.
  • Unscrew the two screws at the back and slide the top cover off the case.

Washing Machine Bosch Does Not Drain Water

  • Unscrew the bolts around the perimeter of the rear panel, set aside.

Below the tank is the drainage system.

Place a cloth and wring out the hose clamp. Remove the element from the seat and clean it from the blockage. You can completely disconnect the nozzle from the machine and rinse with warm water.

Replacing the pump

The path to the pump has already been passed, it remains to check the unit for serviceability. When the washing machine is running, the pump may or may not beep, but it may not pump out liquid. If the impeller is not blocked, then it is worth ringing the electronic winding.

  • Pull off the drain hose clamp and disconnect from the pump housing.
  • Disconnect the pump wiring, turn it to the right and remove it from the machine.
  • Turn on the multimeter. Attach the test leads to the winding.
  • A reading from 0 to 1 ohm indicates a burnout.
  • A three-digit number indicates that the part is in good working order.

In the event of a breakdown, buy an original unit specifically for a Bosch Maxx washing machine or another model. Installation is carried out upside-down.

This shows how to get to the pump through dismantling the front wall:

Why the washing machine “Bosch” does not drain water?

It is worth starting the check with typical problems that could lead to a stop of the drain. Look at the control panel. Make sure the No Drain program is selected. Next, check in the following sequence:

  • Inspect the drain hose. It should be level, without kinks.
  • Disconnect the hose from the body and lower it into the sink.
  • Run any mode.
  • If water flows out of the hose, then the cause is a blockage in the sewer system.

You can clean the sewer using special tools or by calling a plumber.

If the modes and communications of “Bosch Max 5” (Maxx 5) or another model are in order, then the case may be a serious breakdown. Typically, an electronically controlled machine will display an error code. Having learned its meaning, one can come to a conclusion about the location of the malfunction. But if there is no code, then you will have to check in order:

  • drain filter and plug for clogging;
  • pump at the time of breakdowns;
  • water level sensor for malfunction;
  • electronic module for burns and damage.

To find and fix the breakdown, start by diagnosing the internal parts of the washing machine.

The Bosch washing machine does not drain water

Getting ready to take the laundry out of the machine and see that the drum is full of water? The cycle should be over by now, so what’s the problem? The fact is that the Bosch washing machine does not drain water. If you know where to look for a problem, the operation of the equipment can be quickly restored. Check out the causes and solutions to the problem.

How to drain water from a Bosch washing machine?

Have you ever cleaned the drain filter? If not, then the likely cause of the problem is a blockage in the part. The filter protects the pump from the ingress of debris: small wardrobe parts, coins, hair, threads. The waste water passes directly through the filter system, and then is pumped out by a pump and goes into the sewer.

In machines made by Bosch, including the “Bosch Max 4” (Maxx 4). the filter is hidden in the lower right corner, under the loading door. Here’s what you need to do to drain the water and remove the blockage:

  • Open the plinth panel (it can be small or long). Press out the latches with a flat screwdriver.
  • Place a flat container.
  • Rotate the plug counterclockwise.
  • Remove and clean the filter.

At the same time, water will drain from the tank and you can remove the laundry. Also remove dirt from the bore and check the pump impeller.

Blocking the part with foreign objects will stop draining. After that, proceed to inspect the internal parts.

Level sensor check

The pressure switch (aka level sensor) is used to measure the amount of water in the tank. When a part fails, it may send incorrect signals to the module or not work at all. As a result, the control triac does not give a signal to turn on the pump.

The sensor is checked as follows:

  • Remove the top cover of the Washing machine.
  • At the side wall there is a small round piece with outgoing pipes. This is the pressure switch.
  • Disconnect sensor contacts and hoses.
  • Unscrew the fastening screw.
  • Examine the tubes for a possible blockage.

To check the pressure switch, connect a tube to it and blow into it. If you hear clicks, then the part is working. If silence, replace the pressure switch.

A faulty level sensor is a rather rare breakdown. But if other problems are excluded, it is worth checking the pressure switch.

Have all the items been checked and cleaned, but the machine has not started normal operation? What to do? Probably a problem with the control unit firmware. Many users complain about a similar problem with a Russian-assembled Bosch washing machine. Of course, you cannot perform a flashing on your own. Therefore, you need to call the master. Repair will take no more than 20-40 minutes.

As you can see, most problems with a lack of drain are solved without contacting a service center. How to avoid problems? Follow simple rules:

  • Check items carefully before loading into the drum.
  • Clean the drain filter every one to two months.
  • Ensure the correct connection of communications.
  • Install a voltage regulator.

Many users neglect the last point. but in vain. Once you install the stabilizer, you will protect the washing machine and other equipment from voltage surges.

Does not drain water

Washing machine drain does not work. one of the most common malfunctions.

Manifestations:

  • washing stops at the drain, water does not leave the tank;
  • water leaves the tank very slowly and the program fails;
  • there is no water in the tank, but no spinning occurs;
  • during washing, the water is drained, and at the end, after rinsing, it does not drain;
  • water is drained on one wash, not drained on another.

Causes:

  • clogged drain pump filter;
  • blockage of the branch pipe leading from the tank to the pump;
  • the ingress of a large foreign object into the pump impeller and its jamming, after which the pump cannot rotate;
  • clogged drain hose;
  • blockage of the siphon or sewer;
  • the drain pump is faulty.

Repairs:

Disconnect from the network. Disconnect the washing machine from the power supply!

Pump filter. Check pump filter for clogging. It is located on the front wall of the washing machine, below, under a small hatch, on the right or left. The washing machine does not drain water if the filter is clogged. It is necessary to unscrew it and clean it.

Before unscrewing the filter, we tilt the machine back and substitute a container for draining the water under it, unscrew it carefully so as to have time to screw it back when our container is full.

Pump impeller. Check the pump impeller. It is located behind the filter. You need to shine a flashlight into the hole from where the filter was unscrewed, and check the impeller itself and around it. Even a small object (coin, toothpick, hairpin, etc.) may cause the pump to malfunction and the water will not be drained. If a foreign object is found, remove it by hand or with tweezers.

Clean the drain connection. If, after removing the filter, the remaining water has not drained from the tank, then this means that the pipe connecting the tank to the pump is clogged. Then, for convenience, you need to disconnect the pump from the body of the washing machine, or rather not the pump itself, but the entire drainage unit or pump chamber. This is a plastic part that allows you to connect together the pump, drain pipe and drain hose, as well as fix this entire unit to the body of the washing machine. The pump chamber is mounted on screws, after removing which, it is easy to detach it from the body and it will be easier to get to the nozzle.

You need to act carefully. Disconnect the end of the pipe, which is attached to the pumping chamber with a powerful clamp and gradually clear the blockage by cleaning the corrugated rubber pipe and gradually draining the water from the tank into the prepared container. Then reconnect the branch pipe to the pumping chamber, just as it was in the beginning, without changing anything. If, after removing the filter, all the water flows out of the machine, then the drain pipe must still be checked for blockage by probing it along its entire length and if foreign objects are found in it, carry out the procedure for cleaning it.

Pump serviceability check. After completing the previous steps, it is necessary to check the serviceability of the drain pump. To do this, connect the washing machine to the power supply and select the “drain” program (if not, then “spin”). In this mode, the pump should start rotating, which can be observed in the filter hole. You need to shine a flashlight there and understand whether the pump impeller rotates or not. If it does not rotate, then the pump must be replaced.

The first steps for replacing the pump are similar to cleaning the pipe connecting the tank with the pump from clogging, only the pipe itself can not be disconnected from the pumping chamber. After the machine is tilted back and the pumping chamber is disconnected from its body, it is necessary to disconnect the pump itself from the power supply wires and from the pumping chamber itself. Basically, modern washing machines are equipped with drain pumps of several of the most common types, which are usually on sale.

One more subtlety. A situation may arise when the water does not drain, but everything is in order. You have removed the filter, checked the branch pipe and the drain hose, but there are no blockages, and you can see that the pump turns when the “drain” program is selected. There are two options. either the drain hose is clogged and the hose needs to be cleaned, or the pump has exhausted its resource and turns only to “dry”. That is, it can twist without water, but wedges with water, it lacks power. Such a pump must also be replaced.

Check after repair. After eliminating the malfunction and complete assembly, you must first visually check all the connections affected by the repair and the electrical wires supplying current to the pump. Then check the operation of the washing machine in all modes. If everything is in order, disconnect the washing machine from the mains again, tilt it back and illuminate it with a flashlight, check all connections for leaks and leaks. If you see traces of leaks on any connection, then you need to disconnect and reconnect it more carefully, then check everything again.

Surgical method or second aid to the washing machine

Car repairs. quite an expensive pleasure, which depends on its brand as well, because often the master increases the price several times, only after hearing the brand. In reality, the parts are not that expensive. For example, a water supply valve with an application for Italian costs within 500 rubles. If a master takes over its replacement, you will give him about 5,000 rubles for the work.

The most common problem when the machine won’t fill with water is a valve problem. And most often it needs to be replaced:

  • We observe all precautions by shutting off the water and disconnecting the washing machine from the network. In the first step, we disconnect the hoses from the valves (which are located at the back of the machine), since water often remains in the hoses, you need to prepare a container to drain it.
  • We unscrew the fasteners of the upper cover of the washing machine.
  • The connectors of the wires from the coil, as a rule, have bright colors (for example, blue and red), similarly to blockbusters, you need to remember their location and disconnect them.
  • Using the pliers, remove the fasteners from each of the four hoses. Note the location of the hoses and disconnect. Keep in mind that they may contain water too, so it’s best to prepare a towel.
  • We unscrew the screw on which the valve is attached (it is located at the back) and take out the inlet valve itself.
READ  Washing Machine Samsung Change Bearing Video
  • We install a new valve for water supply by placing it in the bracket and securing it with a screw using a screwdriver.
  • We attach the hoses to the connectors and fix with clamps. We connect the coil wires.
  • We put back the cover of the washing machine, returning it to its original position, and fasten the cover with screws behind the machine. We connect the hoses to the new inlet valve.
  • We connect the water and turn on the washing machine to the outlet, check its performance.
  • The Tubular Heater in the washing machine is defective, therefore water does not flow into the tank. To replace this element, follow these steps:

    • Opening the back cover of the washing machine.
    • Temperature sensor connected to Tubular Heater, ground terminal. To remove these wires, use pliers, pull out the connectors.
    • And then we take the socket wrench and unscrew the nut that holds the Tubular Heater.
    • Then with a screwdriver, and then with your hands, pull the Tubular Heater towards you with up and down movements, and together with the Tubular Heater you need to pull out the rubber seal. Here again a screwdriver will help.
    • When inserting a new Tubular Heater, be sure to pay attention to its guide, that is, to look into the hole formed from the past Tubular Heater. There will be grooves for tight fit of the part.
    • The rubber seal of the new Tubular Heater is best lubricated with dishwashing gel before inserting so that it can be inserted quickly and easily.
    • Then insert the temperature sensor, tighten the nut and connect the wires.

    Another problem is problems with the washing machine door or with the fact that the door lock does not work. Both the one and the other factor affect the fact that water is not supplied to the machine. The following will help to fix such malfunctions:

    The washer does not draw water into the drum: why and what to do? Common causes of breakage

    There may be several reasons why the washing machine does not collect water, but the most popular ones are presented below:

    • Valve failure. This can already be noticed at an early stage, when the machine has stopped washing off all the powder, and it remains untouched. In order to check the valve, you need to apply 220 volts to the valve, it should close (you will hear a characteristic click). If water is connected, it will pour directly into the drum. In this case, you need to check both valves. If one and the other do not respond, they can be replaced with a screwdriver.
    • The water supply mesh is clogged. Most often, this problem looks like this: the machine takes a very long time to collect water, or there is a characteristic buzzing sound.
  • Problems with the presostat. This is a round part, from which the wire goes to the bottom of the machine, and on which the water supply and its volume depend. To check the operation of the pressure switch, you need to disconnect the tube (which connects the pressure switch itself to the wire) and blow into it. When people leave home for a long period and do not use the washing machine, the pressure switch remains closed in the full tank position. There may be a spider web or some fibers may get stuck, so after “blowing” this problem will be immediately solved. When you blow through the wire, 1-2 clicks can be heard (may vary depending on the brand of washing machine).
  • Control box problems. On the control unit, as a rule, two resistors burn out. In this case, it is possible to change these two resistors and the machine will continue to delight you with its work for many years to come. However, such work can only be done by a master.
  • Also, quite often the wire that goes from the presostat to the bottom of the machine is exposed to wear. As a rule, it begins to leak air. The door lock is also important, because if it is jammed, the washing machine detects that the door is open and therefore does not supply water.

    The next problem, due to which water does not start into the car, is a pump malfunction. If the pump burns out, this is a reason to contact the household appliance repair service, since repairing the pump with your own hands is quite problematic.

    First aid in the absence of water supply

    The main thing to remember is that all the actions to repair the machine that you perform must take place with the water supply tap closed and the washing machine disconnected from the network.

    If the machine does not collect water and you hear a faint buzzing, initially you need to:

    • Check that the tap through which the water is supplied is open.
    • If it was open, then you need to block it. Then disconnect the water supply hose (located at the back of the machine) and lower it into a plastic container. Water will pour out of it.
    • See if the hose is kinked and straighten kinks along its entire length.

    These are the first measures when there is no water supply from the machine. If you noted that everything is fine and nothing prevents the machine from drawing water, the next step is to check the filter of the inlet hose.

    In many models of washing machines, the filling hoses come with an additional filter, which is a small metal mesh. It often clogs up, let’s check it:

    • We unscrew the hose from the washing machine.
    • A valve system appears in front of us, into which a mesh filter is inserted. The filter has a special indent, so we take the pliers and, grasping this indent, pull out (do not unscrew) the mesh filter.
    • The mesh can be cleaned with a needle under the pressure of water and inserted into the valve using pliers

    .

    The next problem, due to which washing water may not collect water, is a hard filter (and again there is a mesh).

    If you have a meter, as a rule, a filter is placed after the tap. In order to cope with the problem, you will need two keys: with one you need to hold the connection with the tap, and the second. unscrew the bolt, and then substitute the container down and open the tap. The filter is cleaned with a stream of water and can be twisted, also holding the connection with the tap with a key.

    Read more articles about washing machines:

    • How to choose a washing machine: http://vse-sekrety.ru/164-kak-vybrat-stiralnuyu-mashinu.html
    • How to clean a washing machine with citric acid: a recipe for an automatic machine.
    • How to extend the life of household appliances, read here.

    What to do if the washing machine won’t draw water?

    Of course, if such a situation occurred immediately after buying a car, it makes sense not to do anything and go straight to the service center with a receipt and a guarantee, or even hand it over.

    But if the car served you faithfully, you should establish the cause, and then take the necessary steps to fix it. First of all, you need to check the water tap and hose, and only then, if there is no result, you can open the lid and start working with the internal elements of the machine.

    Why isn’t water being collected?

    In the next, the master will tell you why the washing machine does not want to draw water. He will also indicate how accurately you can diagnose a particular cause.

    The washing machine is an assistant who also sometimes needs help, which you can organize yourself without resorting to the services of a master. If the machine does not collect water, you will solve almost all possible problems yourself: the filter, the valve, and the door. all this is mounted using pliers and a screwdriver with your own hands.

    Bosch washing machine does not drain water

    Perhaps the most common problem with Bosch washing machines. this is the absence of draining water. As a rule, such a malfunction occurs quite often, regardless of the life of the washing machine.

    The washing machine warning system will notify you of this malfunction by displaying a message with the error code F03. Next, we will look at the main sources of this problem, and how to fix it.

    Malfunctioning drain pump in Bosch washing machines

    Drain pump. this is not the brain of a washing machine, however, it occupies an honorable second place in terms of functions in the operation of this household appliance. The main such function. this is a water drain. For a full wash cycle, a Bosch washing machine performs 2-3 full drains of the tank. And of course, this drain pump has a huge load.

    Under normal use, pump performance is limited to 20 years on average. But, most often, owners of Bosch washing machines apply for repairs within 5-7 years after the start of operation. The human factor accounts for the lion’s share of the causes of malfunctions with this electromechanical unit.

    Characteristic signs by which you know that the pump is already wearing out. this is a buzzing sound at the bottom of the washing machine, as well as a crackling sound when draining. After replacing the drain pump in our service center, repairs will not be required for at least 10 years, if you follow our recommendations.

    Supported Bosch Washing Machine Lineup

    See the list of models below:

    The MAXX 4 series includes two common modifications. Speed ​​Edition and Speed ​​Perfect.

    The most popular models of them are:

    WFC 2062 OE, WFC 1664 OE, WFC 1666 OE, WFC 1665 OE, WFC 1667 OE, WFC 2060, WFC 1262 OE, WFC 1263 OE, WFC 1600 BY, WFC 1662 OE, WFC 1663 OE, WFC 2066 OE, WFC 2063 OE. WFC 2064 OE, WFC 2065 OE, WFC 2067 OE.

    WLF 16180 OE, WLF 20180 OE, WLF 20181 CE, WLF 20164 OE, WLF 16060 OE, WLF 16062 BY, WLF 16164 OE, WLF 20060 OE, WLF 20170 CE, WLF 20271 CE, WLF 20281 CE, WLF 24271 CE, WLF 20281 CE CE, WLF 16260 OE, WLF 16165 CE, WLF 16261 OE, WLF 20062 BY, WLF 20160 OE, WLF 20171 CE, WLF 20260 OE, WLF 20261 OE.

    WFO 1640 OE, WFO 1261 PL, WFO 2050 GR, WFO 1661 BY, WFO 1662, WFO 2040 OE, WFO 2042 OE, WFO 2051 GR, WFO 2060 BY, WFO 2064, WFO 2264, WFO 2440 OE, WFO 2442 OE, WFO 2450, WFO 2451 GR, WFO 2464, WFO 2840 OE, WFO 2864, WFO 1660 BY.
    WFR 2440, WFR 2441, WFR 2466, WFR 2830, WFR 2841, WFR 2866, WFR 3240.

    WFH 2061 OE, WFH 1660 OE, WFH 2461 OE, WFH 1260 OE, WFH 1262, WFH 2060 BY, WFH 2460 OE, WFH 2062 OE.

    Modification of SpeedPerfect and SilencePerfect. a highlight of the MAXX5 series.

    Main lineup:

    WLX 20462 OE, WLX 2048K OE, WLX 20362 OE, WLX 20364 OE, WLX 20161 OE, WLX 16163 OE, WLX 20160 OE, WLX 2036 KOE, WLX 20361 OE, WLX 20480 OE, WLX WLX 20461 OE, 24 CE470 OE, WLX 24363 OE, WLX 20460 OE, WLX 24361 OE, WLX 24362 OE, WLX 24462 OE, WLX 24463 OE, WLX 2448 KOE, WLX 20162 OE, WLX 24163 OE, WLX 20363 OE 1616, WLX 243 WLX 20463 OE, WLX 16161 OE, WLX 16160 OE, WLX 20163 OE, WLX 24461 OE, WLX 24360 OE.

    WVD 24520 EU, WVD 2446 SOE, WVD 24460 OE, WVF 2400 EU, WVF 2401, WVT 1260, WVTI 2841 EU, WVIT 2842 EU, WVT 3230, WVD 24420 OE, WVTI 3240 EU, WVTI 2840 EU, WVTI 2842 EU.

    Main lineup:

    WAE 2037 KOE, WAE 16160 OE, WAE 20440 OE, WAE 24160 OE, WAE 24360 OE, WAE 24440 OE, WAE 20360 OE, WAE 20370 OE, WAE 16440 OE, WAE 20160 OE.

    Main lineup:

    WAE 24463 OE, WAE 24164 OE, WAE 24467 OE, WAE 24443 OE, WAE 2049 KOE, WAE 16161 OE, WAE 20161 OE, WAE 20163 OE, WAE 20164 OE, WAE 20361 OE, WAE 24441 24A66 OE, OE44 OE, WAE 20364 OE, WAE 2047 SOE, WAE 24163 OE, WAE 24468 OE, WAE 20363 OE, WAE 16443 OE, WAE 24444 OE, WAE 24462 OE, WAE 24364 OE, WAE 16163 OE 284, WAE 2444 WAE 28443 OE, WAE 28441 OE, WAE 24361 OE, WAE 20443 OE, WAE 24363 OE, WAE 20362 OE, WAE 24464 OE, WAE 20442 OE, WAE 16441 OE, WAE 20441 OE, WAE 24465 WAE 20441 OE, WAE 24465 WAE 2044 OE, WAE 16444 OE, WAE 2044 SOE.

    Vario Perfect in German means. perfect quality. Sensitive. sensitive wash. These two qualities combine in one of the latest Bosch LOGIXX washing machines.

    Logic 6 lineup.

    WLM 20440 OE, WLM 20441 OE, WLM 24440 OE, WLM 2445 SOE, WLM 2444 SOE, WLM 24441 OE.

    WAQ 20440 OE, WAQ 24440 OE, WAQ 24460 OE, WAQ 24461 SNOE, WAQ 28440 OE, WAQ 28460 SNOE. (AVANTIXX)

    READ  How To Remove Mold From Washing Machine

    Lineup Logic 7.

    WIS 24140 OE and WIS 28440 OE

    Lineup Logic 8.

    WAS 20443 OE, WAS 2474 GOE, WAS 24740 OE, WAS 2044 GOE, WAS 2875 BOE, WAS 24440 OE, WAS 24442 OE, WAS 24741 OE, WAS 28743 OE, WAS 20440 OE, WAS 24742 OE, WAS 24743 OE, WAS 28740 OE, WAS 28741 OE, WAS 24443 OE, WAS 2876 BOE, WAS 24441 OE, WAS 28742 OE, WAS 20442 OE, WAS 20441 OE, WAS 28750 OE.

    We serve professional machines WBB 24751 EU and WBB 24750 EU.

    Lineup of the 2nd series.

    WOT 24552 OE, WOP 2050, WOL 2050 EU, WOT 20351 OE, WOR 16153 OE, WOT 20152, WOF 1800, WOR 20150 OE, WOT 16152, WOT 20350 OE, WOR 16150 OE, WOK 2031, WOL 2051, WOP 2051, WOR 20152 OE, WOT 24550 OE, WOT 24551 OE, WOT 26483 OE, WOR 20151 OE, WOR 20153 OE, WOT 20352 OE, WOL 2200, WOR 16152 OE, WOL 1650 EU, WOL 1670 EU.

    Model range of the 4th series.

    WAN 24060, WAN 20060, WAN 28290, WAN 24260, WAN 24140, WAN 2416 S, WAN 20160, WAN 24290.

    Model range of the 6th series.

    WLN 24242, WLN 24261, WLN 24260, WLN 24262, WLN 24241, WLN 24240, WLN 2426 E, WLN 2424 Z, WLN 2426 M.

    WAT 28541, WAT 24442, WAT 28740, WAT 20441, WAT 24440, WAT 24441.

    WAY 32742, WAY 24742, WAY 28742, WAY 3272 M.

    WLT 24460, WLT 24560, WLT 24440, WLT 24540.

    Model range of the 8th series.

    WAW 28740, WAW 32540, WAW 28540, WAW 24440, WAW 28440, WAW 32590.

    WVH 28442 and WVH 30542.

    Lineup of the Classic series x5.

    WAA 12161, WAA 16160 OE, WAA 16161 OE, WAA 16162 OE, WAA 16163 OE, WAA 16170 CE, WAA 16171 CE, WAA 16260 OE, WAA 16261 OE, WAA 2016 KOE, WAA 2016 SOE, WAA 20160 2016 OE, WAA 20160. WAA 20162 BY, WAA 20163 BY, WAA 20170 CE, WAA 20171 CE, WAA 20180 OE, WAA 20181 CE, WAA 2026 SOE, WAA 20260 OE, WAA 20261 OE, WAA 20262, WAA 20263 OE, WAA 202701 CE, WAA 20271 CE, WAA 20272 CE, WAA 24160 OE, WAA 24162, WAA 24163, WAA 2427 SCE, WAA 24270 OE, WAA 24271 CE, WAA 24272 CE, WAA 2428 SCE.

    WLF 16180 OE, WLF 20180 OE, WLF 20181 CE, WLF 20164 OE, WLF 16060 OE, WLF 16062 BY, WLF 16164 OE, WLF 20060 OE, WLF 20170 CE, WLF 20271 CE, WLF 20281 CE, WLF 24271 CE, WLF 20281 CE CE, WLF 16260 OE, WLF 16165 CE, WLF 16261 OE, WLF 20062 BY, WLF 20160 OE, WLF 20171 CE, WLF 20260 OE, WLF 20261 OE.

    Lineup series Classic x6.

    WFXI 2840 EU, WFB 2001 BY, WFE 2021 EU, WFT 2830, WFK 2431, WFW 3231, WFG 242L GB, WFB 3200, WFB 4001, WFG 2060 BY, WFG 2070, WFX 2440 OE, WFD 2060 BY, WFD 1660 BY, WFO 1607, WFD 2090 EU, WFF 1201, WFG 2420 GB, WFT 2806, WFX 2840 OE, WFXI 2842 EU, WFG 2220, WFB 4800 GB, WFD 1060, WFG 2020 GB, WFK 2831, WFP 3330, WFB 1605 BY, WFF 1401, WFP 3231, WFW 2831.

    Our service center serves any Bosch washing machine. All spare parts are new and original.

    Blockage in the drain system of the Bosch washing machine

    Blockage in the drain system. this is where drain pump problems begin. It is a well-known fact that most often the drain pump fails due to a blockage in the drain system.

    The nature of the blockage is quite natural. This is carelessness in preparation for washing. The most common mistake. This is when the s of things are not checked before washing for small foreign objects that can get into the drain system through the tank. Further, this foreign object enters the impeller of the operating pump through the drain pipe, after which the device breaks down.

    There is a 50% chance that the pump will remain serviceable when blocked. If there is a blockage, it is necessary to urgently drain the water from the washing machine using manual mode. Below the body of the washing machine there is a hole closed with a protective cover. You will need: a container, a doormat and a little patience. Slowly unscrewing this lid, place the container under the hole so that the water will drain there. When the water is completely drained, it is recommended to clean the drain filter and remove the blockage.

    If for some reason you are unable to remove the blockage yourself, we recommend that you contact a trusted service center and get professional help to avoid serious damage during further operation.

    You can call the wizard on the contacts page or by calling the multichannel phone 7 (495) 790-29-43. service center “Bosch”

    Incorrectly selected program

    Automatic washing machines from BOSCH are equipped with a control panel, on which you can independently select the mode of washing, spinning, water temperature and other functions. Therefore, the reason for the non-standard operation of the device may be the wrong choice of program. For example, if you select the “wash without draining” mode, the water will not drain out of the washing machine by itself. Therefore, before calling the wizard, it is recommended to check the correct installation of the program.

    Many models have a “no spin” wash program. It is used for woolen and delicate fabrics to prevent stretching. In this case, the unit will not automatically wring out the washed items and drain the liquid. To drain the water, you must first press “Start / Stop / Cancel”, then “Drain”.

    If the program was set correctly, the external communications are working, and the Bosch washing machine does not drain the water, then something has broken in it. In such a situation, you need to remove the laundry and drain it manually through the drain filter located at the bottom of the household appliances. In order not to spill water on the floor, an empty container must be placed under the filter.

    Bosch washing machine does not drain water

    Today every family has their own washing machine. At the same time, many of these household appliances are fully automatic, there is a washing and spinning mode. But electrical engineering tends to break down for various reasons: the BOSCH washing machine does not drain water. Therefore, many are interested in what the problem might be, and how to solve it on their own.

    Cleaning the nozzle

    Dirty water after washing things goes through the filter. Anything that is trapped by the filter mesh settles in the pipe. This part is connected to the pump. Therefore, in order to clean the pipe, you need to know how to get to the pump. Most BOSCH machines have a removable bottom. But, even after removing it, access to the details of the device is blocked by the transverse bar.

    What to do:

    • Disconnect the device from the power supply and communication systems.
    • Close the inlet valve (tighten the valve). Pressing the latch, pull out the dispenser tray.
    • Unscrew the bolts at the back, slide the top cover off the body.
    • Unscrew the screws on the rear panel, move it to the side.
    • Find the drainage system under the tank.
    • Lay a rag on the floor, loosen the hose clamp.
    • Remove the branch pipe from the seat and clean it from the collected dirt.

    If the branch pipe of the Bosch Maxx 5 washing machine is very dirty, it can be completely disconnected from the unit and washed in a basin of warm water.

    Pump repair

    The pump during the operation of the washing machine may make a sound, hum, but not pump out water. This indicates its malfunction. The reason may be that foreign objects (coins, buttons from clothes, threads, hair, etc.) get into the snail of the drain pump. All this debris contributes to the destruction or jamming of the impeller blade. And if the unit has been used intensively for several years, then the parts could wear out naturally.

    Incorrect system operation

    Unpredictable, unsystematic behavior of the washing machine usually indicates a breakdown of the control unit. Stops, long pauses in wash cycles, a strong discrepancy between the real time of programs execution and the declared duration are sure signs of a brain breakdown. Also, the machine may simply not turn on, not wring out, not open at the end of the program.

    In devices with electronic control, the board must be replaced. The procedure is not complicated, but the cost of a part can be up to half the price of a new machine. Electromechanical models with a programmer allow you to “reflash” it

    Engine problems

    Motors in Bosch washing machines come in direct drive and collector drives. The latter are equipped with carbon brushes, which create an electromagnetic field in the engine rotor when rubbed against its walls. The wear of the bristles makes it impossible to start the engine. They need to be replaced.

    Other problems may be related to the electrical system: power surges, turn-to-turn faults in the motor windings, etc. Such malfunctions are usually rectified at the service center.

    Error codes

    Error codeMalfunctionCauses and remedies
    F01Hatch door not closedMake sure that the door is tight and there is a characteristic click when closing. The locking device or the closing sensor may be out of order. The door assembly can be replaced in its entirety or disassembled and replaced with what is needed: hinge, locking tab, etc.
    F02Water does not flow insideVerify:

    Next, you need to repair the motor. Change if necessary.

    Intake valve or drain pump broken.

    Defective pressure sensor.

    Mains voltage problems.

    The drum bearing is out of order.

    CPU error.

    There is no water heating

    If the machine has stopped heating the water completely, the automation will report this with a corresponding error. But a situation is possible when heating is insufficient or slow. You can understand this by the increased runtime of programs (especially if you wash at high temperatures). The reasons may be as follows:

    • Temperature sensor (thermostat) breakage

    The sensor looks like a silver cylinder. It is inserted from the outside into the Tubular Heater opening. There is a wiring from the sensor to the control board. If the wiring is intact, the sensor cannot be repaired and needs to be replaced.

    • Malfunctioning Tubular Heater

    Tubular Heater is a metal coil with an electrical conductor and a fuse inside. It is inserted into the working cavity of the washing machine under the drum, where it heats the water. Outside, voltage and ground from the control unit are connected to its terminals.

    The failure is associated either with a burnout of the electrical circuit (blown fuse), or with scale on the coil due to lime deposits. If the circuit of the coil itself is intact, then you can clean the working part of the heater with citric acid or special descaling agents. Otherwise, replacement of the Tubular Heater is necessary, which is not very difficult.

    • Failure of the control module

    If the “brain” of the washing machine is out of order, the heating command (voltage) is not sent to the Tubular Heater, and the malfunction may appear intermittently and unpredictably. In this case, only flashing or replacing the board can help.

    Replacement of Tubular Heater

    The first thing to do is to access its terminals. It is enough to remove the back cover of the machine.

    Then you should exclude a possible breakdown to the case: consistently make sure that there is no circuit between each of the terminals and the case.

    Next, you need to check the continuity of the circuit between pins L and N and measure the resistance between them. Depending on the power of the heater, it should be within 24-28 Ohm (R = U2 / P). For example, Bosch maxx 4 has a Tubular Heater power of exactly 2 kW and an impedance of 24.2 ohms. If it is very small or very large, replacement is necessary.

    When buying a spare part, you need to pay attention to the parameters:

    • power (always indicated on the heater itself);
    • length (too long may not fit into the tank);
    • a hole for a thermal sensor (should be, if there is in a broken sample);
    • rubber seal curb (similar).

    The latter is very important because in the absence of a curb, water during filling into the tank will flow directly to the contacts of the Tubular Heater. Silicone grease on the rubber part is useful for easier insertion of the Tubular Heater into the connector.

    The drum is not spinning

    If the engine is working properly, but there is no rotation, you should enumerate the options.

    • Tank lock

    Eliminate any mechanical blocking of tank rotation. A foreign body can be located both inside and outside of it.

    • Drive belt wear

    The rubber belt transmitting rotation from the motor shaft to the drum shaft can shift, break, stretch. To check it, just remove the back cover. It is easy to change independently, you just need to purchase a spare part strictly in accordance with the article number of the machine.

    • Control unit malfunction

    Failure of the control module is diagnosed by excluding other causes and a start-up breakdown from an “external” known good board. As a rule, it can only be repaired in workshops.

    Diagnostic Mode

    Washing machines do not display all of the errors described below on the display or through the indicators. To obtain the most complete information, there is a diagnostic mode, which can be entered through the sequence of switching controls. Consider the example of the bosch maxx 5 model (similarly for bosch maxx 6 and bosch maxx 7).

    • Turn on the machine, close the door.
    • Move the program selector to the vertical position.
    • Wait 2-3 seconds.
    • Move the selector to position 8.
    • Wait for the Start / Stop button to flash.
    • Press and hold the “Spin revolutions” button.
    • Move the selector 1 position clockwise.
    • Release the button.
    READ  How To Open The Lid Of A Washing Machine Bosch

    The last malfunction of the washing machine will appear on the display of the washing machine or through a combination of indicators.

    To start a new test, you must select the analysis program with the selector.

    PositionTest item
    1
    2
    3Engine
    4Drain pump
    fiveTubular heater
    6Hot water inlet valve
    7Water inlet valve for mains and pre. washing
    8Water inlet valve for main. washing
    nineWater inlet valve for pre washing
    tenSound test
    elevenAuto test
    12Auto mechanic test
    thirteenAutotest not mechanic
    fourteenQuick auto test
    fifteenQuick auto test

    Water does not drain

    The drain hose might be kinked or kinked. It is also worth unscrewing and checking the filter of the washing machine, located in its basement. If it is also clean, you can try disconnecting the drain hose from the drainage point and running the drain program into the bathroom, sink or large container. This will prevent clogging of the siphon (if any) or sewer pipes.

    • Broken water level sensor

    If the sensor is broken, the control board may stop the drain pump ahead of time or not start it at all.

    • Broken pump

    Pump (or drain pump). a small motor with a plastic impeller that pumps water into the drain system.

    A sure sign of its failure is a quiet low hum of the car when trying to drain the water and there is no murmur of water at the same time. The windings of the pump motor are buzzing, but the mechanism itself is not spinning. The cause is often lime deposits.

    Part needs to be replaced.

    DIY washing machine repair tips

    Incorrectly selected program

    The Bosch Maxx 5 models have a “no drain” wash mode, designed for delicate fabrics. An incorrectly selected mode can cause non-standard behavior of the mechanism. Therefore, before calling the master and opening the unit, you need to make sure that the washing mode is correctly selected.

    Pump malfunction

    Another reason why a Bosch washing machine does not drain is a pump failure. In this case, the washing machine does not drain and hums. During proper draining, a specific, muffled hum is heard. A pump malfunction is eliminated by a technician. A breakdown may occur due to an old pump, which has worn out for a long time.

    Also, small debris that has penetrated the filter can lead to malfunctioning of the pump. Hair, threads or wool could be wound around the pump, so it will not be possible to do without a detailed analysis of the mechanism. If the Bosch washing machine hums while draining the water, there are periodic interruptions in the water drain and spinning. these are sure signs of the need to replace the pump.

    Malfunctioning module and wiring

    The reason for the lack of water extraction in the Bosch washing machine may be a broken wiring inside the mechanism. A home appliance repairman will be able to identify this problem. Also, burnt-out microcircuits and interruptions in the unit’s firmware are a possible reason for the lack of water drainage. In each situation, the wizard determines whether it is possible to repair the module, or whether it is necessary to completely replace the programmer with a new one.

    Bosch washing machine does not drain water. what to do

    • Why does not the water drain
    • Clogged filter
    • Pump malfunction
    • Malfunctioning module and wiring
    • Incorrectly selected program
    • Checking the machine after repair

    Each owner of a Bosch washing machine had to deal with technical problems of a different nature. The rest of the article will discuss what to do if your Bosch washing machine does not drain. And what causes the breakdown.

    Clogged filter

    When loading dirty clothes into a washing machine drum, housewives often forget to check the contents of their s. Therefore, the filter may contain such items: coins, paper, lint, small toys and other things. In Bosch washing machines, water enters the drain hose through the filter, and not directly from the pump.

    This protects against clogging of sewer pipes and keeps things forgotten in s. A clogged filter is one of the reasons why the machine does not drain and wring out. In this case, the automatics displays an error code indicating a malfunction.

    On Bosch models, access to the filter is at the bottom of the front panel. It is important to remember that when opening the panel, cover the floor around with rags, because the water left in the pump may flow. If this does not happen, then the branch pipe that connects the tank and the pump is clogged. This cleaning is performed by the master. Carefully removing the filter from the washing machine, it must be cleaned of dirt, rinsed and returned to its place using the steps indicated in the instructions. This kind of preventive cleaning should be done systematically.

    Why does not the water drain

    When a Bosch washing machine breaks down, the repairman is most often called. But in some cases, a malfunction of an important technique must be resolved immediately. Certain types of technical problems can be corrected independently, even in the absence of special skills. A common type of breakdown is the lack of water drainage and spinning. In the Bosch Maxx 4 models, the following signs are observed:

    • When the water is drained, washing stops. The water remains in the drum.
    • Slow drainage of water from the tank, due to which a violation of the mechanism system occurs.
    • If there is no water in the drum, spinning is not performed.
    • The water is removed during the wash process and remains in the tub after rinsing.
    • Drainage occurs only in certain wash modes.
    • The machine hums at the end of the work process, the water is not drained.

    Owners of Bosch laundry equipment should know what to do if the drain and the spin system are disturbed. If the Bosch washing machine stops draining water and spinning the laundry, you need to check the settings and the set washing mode. Some modes assume no spin, designed for delicate fabrics.

    To do this, disconnect the hose and hang it over the sink or bathtub. Having included one of the washing modes, observe the flow of water. If the head is free, then the sewer system is clogged. To clean it, you need to call a plumber.

    Checking the machine after repair

    After that, the Bosch machine needs to be started and the washing process repeated in all modes. If the mechanisms are in good working order, disconnect the unit from the network, tilt it back and check the integrity, tightness of the connections, eliminate the presence of leaks. If some connections have a leak, then you need to eliminate it by carefully examining all the details, the pump. After checking the washing machine is ready for further use.

    To prevent damage to the drain system in the Bosch classic 5 models, you need to check the clothes before loading into the drum. Small parts and objects can clog the filter and pump, which will stop the spinning and draining process.

    In case of serious breakdowns, contact the repairmen and the service center. In some cases, troubleshooting yourself can lead to more serious damage. Timely prevention and respect will extend the life of your Bosch washing machine.

    Cleaning, changing the filter

    Before opening the door, cover the floor underneath with rags (a little water will leak out). Opening the hatch, you will see the filter itself, which is tightly screwed into the seat through a rubber gasket. Next, you will see a knob that needs to be turned counterclockwise. This is usually difficult to do. The reasons are obvious: if the filter was not unscrewed before, then it sticks to the rubber gasket, so the washing machine does not drain water.

    On some models, this part is secured with additional screws. Inspect the filter and carefully clean it of debris. If there is no debris, then the filter is not the reason for the lack of drainage.

    There is also such a situation: after installing the cleaned filter in place, the drain still does not occur. In this case, pull out the filter again and shine a lantern inside the hole: there you will see the impeller of the water pump. Try to scroll it with your hand. If the rotation is tight, there may be thread wrapped around the impeller. If the pump is clean, then there is a possibility that it is out of order. If the pump is working properly, we continue to think about how to drain the water from the washing machine and why it does not work.

    [iframe src = “http://www.youtube.com/embed/uIZA4qhCSkc” frameborder = “0 ″ width =” 425 ″ height = “350 ″]

    Software failure and electronic module

    It so happens that the machine stopped working during an intermediate or last spinning process. In this case, you can try to terminate the program by unplugging the power cord and starting the process again. If the result is negative, the program is interrupted using the buttons: you must try to turn on rinsing and spinning. If the pumping of water has not begun, then you will have to turn to electronics. But here you will not be able to do anything yourself. you will have to hand over the unit to the workshop. Sometimes the replacement of the module helps to restore functionality, but the decision is made by the master.

    Filter

    Laundry and clothes (especially woolen clothes) may leave threads and lint in the machine during washing. In addition, it often happens that some small items remain in the s. A modern machine sends used water to the sewer through a filter. It protects the sewer system from clogging, and on the other hand, it “saves” things forgotten in s, leaving them in the unit.

    A clogged filter is the most common cause of no drain. Usually, when the filter is clogged, a corresponding signal appears on the control panel. Read the instructions, for sure there is detailed information on what to do in such cases. If the washing machine does not drain the water, then the filter will have to be removed (usually it is located at the front at the bottom).

    Different models open the filter cover differently. What to do to remove it:

    • remove the screw and slide the panel to the side (BOSH);
    • use a flat screwdriver to turn the special hooks 90 degrees (old BOSH models);
    • move the upper, then lower latches (ARISTON or INDESIT);
    • just press with your hand;
    • use a knife or flat screwdriver to open.

    What to do if the washing machine does not drain water

    To understand why the machine does not drain water, you must first understand how the process of pumping water out of the tank takes place. Here, the main device is a water pump (pump), which is an engine on which an impeller is mounted. When the motor rotates, the water goes through the hose into the sewer. It can be assumed that the lack of drainage is caused by a pump breakdown. However, in practice, there are many other reasons due to which the machine does not work. Which ones?

    Drain hose

    How is the lack of drain related to some kind of hose? The fact is that this design is a kind of valve that does not allow water to pour out of the unit during washing. The hose itself is connected to the sewer in the form of a loop; and its top should be above the tank of the machine (this should be remembered during installation). The height must be exactly maintained: if the hose is above the water level, then the pump simply does not have enough power to pump the used water. Perhaps you installed the hose incorrectly when moving the unit to another location, in which case the display will indicate an error.

    To make sure that the machine does not drain because of the hose, it must be disconnected from the sewer inlet by placing one end in the basin. Now start the wash in the machine, wait for a little water to fill it, then turn on the drain mode. If the drain has begun, then you just need to adjust the height of the attachment of the upper part of the hose. If there is no water, it will have to be removed. The fastening of the hose is simple. usually these are clamps that attach it to the tank nozzle, which contains the water pump and filter. The disconnection process is simple, but in some cases, to get to the connection point, you have to disassemble the machine.

    After disconnecting the hose, check if it is leaking water. If necessary, it must be cleaned or replaced with a new one. Along the way, inspect the pipe. it may also be clogged. If all your efforts were in vain, then you will have to call a master who will decide whether to take your unit for repair or the malfunction can be eliminated on the spot.