How To Change The Bearing On A Washing Machine Ariston

Dismantling the tank

To get to the drum and replace the bearings, you will need to disassemble the tank. The sequence of actions is as follows:

  • Turn the water tank over with the pulley upwards, block the pulley from twisting with a screwdriver or a metal rod, unscrew the fastening bolt. If it does not turn, grease with WD-40, wait a little, then repeat the steps.
  • Disconnect the pulley, there is a shaft under it. To knock it out, you need to find a bolt similar to the fastening one, screw it into the shaft and knock out the shaft with careful hammer blows at right angles.

Now you need to disassemble the tank. In different models of Ariston washing machines, it can be collapsible (two halves are bolted together) or non-separable (two parts are welded along the seam). In the first case, you just need to unscrew the bolts, in the second, use a hacksaw and cut the tank along the seam. First, you should prepare the bolts that will twist the tank after replacing the bearing and drill the corresponding holes along the seam. These steps can be performed after the tank has been cut, but is slightly heavier.

After the tank is disassembled and separated into two halves, you need to pull out the drum.

Replacing the bearing in the Ariston washing machine

How To Change The Bearing On A Washing Machine Ariston

Using an Ariston washing machine for a long time will result in bearing failure. This malfunction is evidenced by extraneous noise that appears during the execution of the program and gradually increases, and during the spin cycle, a very loud hum and knock is heard. If such signs are found, it is necessary to urgently replace the damaged part in order to prevent even greater damage and breakage of more serious components. To do this, you can invite a service center representative, but if the user wants to save a significant amount of money, he can change the bearings on the Ariston washing machine on his own.

Reasons for malfunction

Bearings usually work properly for six to ten years. But in the course of regular operation of the washing machine, the oil seal begins to deteriorate, which closes the unit from moisture. It hardens, holes and cracks appear on it. Water enters the seat through the holes and flushes out the grease. This leads to significant friction and deformation of the bearing.

Also, improper use of equipment can lead to bearing damage. Constant overload and resulting imbalance negatively affect the condition of the part. In addition, a factory defect is also possible, which will eventually manifest itself.

If the owner of the Ariston washing machine hears a loud hum, knock or other extraneous noise during washing, this indicates a deformation of the bearing. To verify this, you should open the hatch and try to turn the drum manually. If the bearing breaks down, a strong backlash will be felt. In this situation, it is recommended not to postpone the repair, but to urgently replace the faulty bearing. Delay threatens with failure of the shaft or other expensive units of the washing machine.

Replacing bearings

Before replacing bearings, inspect the shaft and sleeve for damage. If they are significantly damaged, they need to be replaced with new ones, otherwise the Ariston washing machine will need a new repair in the near future. If they are intact, they should be cleaned of dirt and rust. To clean the shaft, you can use fine sandpaper, for the sleeve it is better to choose a soft sponge or rag.

It is also required to check the integrity of the cross, with which the shaft is attached to the drum. If it is destroyed, you will need to replace it along with the drum.

Now you need to knock out the bearings, you should start with the outside. It is necessary to turn half of the tank upside down and, taking a chisel and a hammer, remove the part. The blows should be applied correctly on the outside of the bearing, evenly around the circle; you must act very carefully so as not to break the seat. After completing the process, the part needs to be turned over and the inner bearing is knocked out in the same way.

Next, you need to lubricate the nests with WD-40, wipe off dirt and rust, wipe dry, apply special grease and drive in the bearings one by one. first the inner one, then the outer one. Parts are driven in by blows on the outside and evenly around the circle, while you need to ensure that there is no skew. Next, install the oil seals.

Ariston tank and washing machine assembly

After the bearings have been replaced, you need to start assembling the tank. The seams of the two halves should be carefully treated with silicone sealant, then aligned and bolted.

The Ariston washing machine is assembled in the reverse order, if the user took photos during disassembly, then in accordance with them. It is especially recommended to act carefully when connecting the wiring.

After the washing machine is assembled, it must stand as long as it takes for the sealant to completely cure. After that, it must be connected to communications and electricity, pour a little washing powder and perform a test wash. Thus, the equipment will be cleared of residues of dirt, grease and unpleasant odors that remained inside after repair. At the end of the program, you need to look under the washing machine and make sure that moisture does not form under it.

If during the work no extraneous noise was observed and the equipment does not leak, this indicates that the repair was completed successfully.

In order to prevent future breakdowns, it is necessary to use the Ariston washing machine with care, avoid overloading, and distribute bulky laundry evenly. This will significantly extend bearing life.

Dismantling the Ariston washing machine

When disassembling the Ariston washing machine, it is recommended to photograph the technician before removing each part, especially before disconnecting the wiring. This will avoid incorrect actions and prevent equipment breakdown as a result of improper assembly.

To disassemble the Ariston washing machine, you need to follow these steps:

  • Unscrew the screws holding the top cover, slide it back, remove and set aside.
  • Unscrew the bolts, disconnect the upper counterweight.
  • Unscrew the fasteners and remove the rear cover.
  • Turning the pulley wheel carefully, remove the drive belt.
  • Pull out the detergent drawer and unscrew the fasteners behind it holding the control panel.
  • A few more self-tapping screws hold the panel from the inside of the Ariston washing machine, you need to unscrew them, carefully squeeze the latches, then, after taking a photo of the connection, disconnect the wires and move the panel to the side.
  • Disconnect the connection to the reservoir from the detergent drawer and the inlet valve.
  • Remove the hose from the pressure switch to the tank.
  • Remove niche for powder receptacle.
  • Open the hatch, pry on and remove the clamp, disconnect the cuff.
  • Unscrew the fastener and remove the hatch locking mechanism.
  • Unscrew the fasteners and remove the hatch door.
  • Remove the lower decorative panel on the front part, unscrew the fasteners under it and in the upper part, remove the front wall.
  • Disconnect the wires going to the heating element and the motor.
  • Pull out the engine.
  • Remove Tubular Heater.
  • Disconnect the lower counterweight.
  • Remove shock absorbers and suspension springs.
  • Pull the tank up and out of the washing machine.

Preparing to replace bearings

To replace the bearing in the Ariston washing machine, the equipment must be disconnected from the water supply, sewer and network, and then moved to a place convenient for work. You will also need to drain the remaining water, this can be done through the emergency drain hose. It is located at the lower front of the washing machine, under the decorative panel. If it is absent, the liquid can be drained through the filter located in the same place. Taking this opportunity, the part can be cleaned of debris and dirt that could have accumulated there over the years of operation.

Further, tools and spare parts are prepared. To carry out the work you will need:

  • a set of flat and Phillips screwdrivers;
  • set of socket wrenches;
  • silicone sealant;
  • mallet or hammer.

You can replace the bearings on the Ariston washing machine yourself at home, without the help of specialists. To do this, you need to purchase new parts, select a tool, and then carry out repair work according to the instructions. It is recommended to record each action on the phone in order to avoid mistakes during the assembly of the Ariston washing machine.

Need to know: how to change bearings on an Ariston washing machine

Parts are attached in different ways, and the disassembly option may be different. However, the most common are 3 options, which are the most optimal and are found in everyday life.

Namely, in:

  • Crosspiece;
  • Tank;
  • Rear tank cover.

Replacing the bearing of an Ariston machine is one of the most common problems faced by a consumer. The replacement is carried out according to the scheme. It is necessary to disassemble the tank, remove the pulley and divide the tank into 2 parts. Now you can knock out the bearings, first in a circle external, then internal. Internal must be removed with an oil seal.

It is better to remove bearings with a special universal puller.

It is necessary to clean the holes, lubricate the elements with special grease. The installation can now be carried out starting with the inner bearing. After the oil seal is installed, it must be lubricated with a waterproof grease. The external bearing is arranged similarly. Next, the tank and all parts are assembled according to the standard scheme.

  • How to replace a bearing in a washing machine: tools
  • Tips: how to remove a bearing from a washing machine drum
  • Instructions: how to change bearings on an Indesit washing machine
  • We figure out how to change the bearing on a Samsung washing machine
  • Need to know: how to change bearings on an Ariston washing machine
  • Self-replacement of the bearing in the Atlant washing machine
  • Replacing a bearing in a washing machine

We figure out how to change the bearing on a Samsung washing machine

Removing the case is the same as described above. Next comes the disassembly of the tank of the Samsung machine and removing the drum yourself to change the cage, bearings. Racks, removed earlier. The staples and clamps can be removed with a screwdriver or horn, it is not difficult. Next, the top of the tank body is removed and the drum opens. Then the bottom of the case is removed.

READ  Washing Machine Jumps When Spinning What To Do

This will result in 3 large elements:

  • Top of the tank body with a hatch in the middle;
  • The bottom of the tank body with a heater;
  • Drum body with axle.

You should not be puzzled by just replacing bearings, you need to check all the details one by one. In particular, it is a good idea to check the surface of the tank and Tubular Heater for limescale deposits. If it is, it must be removed. Then you can start removing the bearings. The aluminum sleeve contains 2 elements. The large one must be knocked out from the outside inside the tank body using a hairpin and a hammer, the small one must be knocked out the other way around.

Attention! You cannot knock out at one point. It is necessary to beat at 3-4 points, otherwise the bearing will not go smoothly and get stuck in the bushing.

Used oil seals must be removed and the bushing must be wiped from the inside. New oil seals, lubricated with grease, are put in place. The bearings fit into place until they hit the shelves. The bearing fits into the sleeve, it must be seated by hand as far as possible. A block of wood must be placed on top of the bearing. The block is hit with a hammer until the bearing fits into place. This completes the replacement. It remains only to assemble the machine in reverse order. Any model, be it Samsung or Beko or another, must be assembled carefully and in the reverse order.

How to replace a bearing in a washing machine: tools

Usually, the breakdown of washing machines, for example, Indesit, is associated with the failure of bearings. To find out that the bearing has flown is simple. the drum, rotating, makes a lot of noise, when the laundry is wrung out, an unusual hum occurs, the rotation of the drum is disturbed, during washing, the machine vibrates and makes noise. All this signals that the device has broken down, and it’s time to disassemble your favorite Indesit, replace the bearing.

To replace the bearing in the unit, the following tools must be prepared:

  • Regular screwdriver;
  • Curly screwdriver;
  • Pliers;
  • Key for 17;
  • Key for 19;
  • 6 hexagon;
  • Hammer.

After all the tools are ready, you can proceed with the repair, following the proposed instructions.

Self-replacement of the bearing in the Atlant washing machine

You can press the bearings into the Atlant 45u102 washing machine yourself. First, you need to disassemble the machine in a standard manner, and after separating the tank, you can start dismantling.

Strikes must be applied at an angle, at several points, so that the mechanism does not crumble.

If damage to the bushing is visually visible, the entire cross must be replaced. If everything is without problems, then you need to walk with fine sandpaper along the surface of the shaft and sleeve. The removed bearings must be cleaned, sandpaper the places where the new ones will be pressed. It is important to pay attention to the sleeve, it must not be damaged.

Namely, to be:

  • Smooth;
  • No furrows;
  • No scuffs.

For pressing, it is good to use outer rings from worn bearings, this will eliminate the risk of damage. Then it is necessary to perform the device of a new oil seal, having previously lubricated it with a special grease.

Replacing a bearing in a washing machine: how to change Indesit with your own hands, remove a Samsung drum, knock out an Ariston

For a high-quality and quick replacement of a bearing in a washing machine, it is better to turn to specialists. But, if a person has the knowledge and skills, he is sure that he can solve the problem with his own hands, then bearing replacement should be done carefully and carefully.

Tips: how to remove a bearing from a washing machine drum

Disassembly, repair and assembly are carried out carefully, you must start by disconnecting the equipment from the power supply and water supply. The second step is preparing the workplace. It shouldn’t be crowded and dark. Next, you need to remove the cover by loosening 2 bolts and pulling it towards you. Then you also need to do with the back cover, setting it aside.

It is imperative to carefully disconnect all electrical wires of the motor and heating element, remove the ground terminal.

Next, you need to remove the drive belt, unfold the machine, remove the rubber casing from the front wall, pushing the clamp lock with a screwdriver, remove it. Then turn the front panel away from you. Next, the connector is removed from the engine on a typewriter, releasing the latch latch. The branch pipes are disconnected from the drum casing (the clamps must be loosened using screwdrivers and 7 heads).

Upper connection:

  • Pull up;
  • Make an effort;
  • Unscrew the self-tapping screw that holds the level sensor on the casing.

Then you need to pull out the temperature sensor by pushing it through the hole in the pipe. The next step is to get the shock absorbers using 17 and 19 wrenches as levers. It is imperative to drown the tongue on the bushing. Next, remove the drum from the springs. The drum is heavy so you may need help.

The next step is to take the head at 13 and remove the front counterweight. It is necessary to carefully lift it, unscrew the engine fasteners and remove, pushing it forward. At the final stage, using a 6 hexagon, it is necessary to unscrew the pulley, remove the counterweight from the back. Using a screwdriver that acts as a lever, carefully remove the counterweight from the rails and remove the Tubular Heater. Next, there is an independent removal of the gland and retaining ring with pliers.

The bearing is knocked out with a hammer. It is necessary to change carefully. To knock out, it is necessary to knock evenly around the bearing perimeter using a tool. Reassemble in reverse order. A new bearing, before being inserted into the machine, must be lubricated with a special heat-resistant grease.

Instructions: how to change bearings on an Indesit washing machine

The first step is to remove the top cover to get to the insides of the equipment. You need to open 2 self-tapping screws at the back. Next, you need to remove the dashboard. But, having previously removed the compartment, you need to simultaneously press the button and pull it towards you.

You need to prepare the following tools:

  • Pliers;
  • Sealant (silicone);
  • Hammer;
  • Phillips screwdriver and minus;
  • Metal rod;
  • Open keys.

If everything is ready, then you can disassemble. To remove the dashboard, you need to unscrew all the screws. Next, the bottom panel is removed. To do this, you need to use a screwdriver. Once both panels are removed, the front of the unit must be removed. But, first, you need to remove the cuff. She will get in the way. After removing the cuff, it is necessary to unscrew the screws and carefully remove the wall. Then you need to detach the wires that connect the front panel on the washer and the lock of the loading door.

When the parts are removed, you need to start disassembling. The tank itself includes 2 halves, bolted or latched. It is necessary to remove the pulley after dividing the tank. Then it is necessary to remove the drum by disconnecting it, it is necessary to inspect the shaft, bushing and cross to make sure that the parts are in order.

If the machine works in a faulty condition for a long time, then the parts may break.

If you can’t find the problem, you need to disassemble. The first step is to remove the oil seal. The next step is to remove both bearings. For this, a hammer and a metal rod are used. The bearings are knocked out and it is important to avoid damage to the drum. Next, you need to well clean the place where they were sitting. It is necessary to insert bearings starting with a small one. When the replacement is done, it remains to assemble the Indesit model.

When the machine is assembled, it is imperative to carry out a test wash to ensure that it functions normally. This applies to any model, it does not matter which cars are repaired by Indesit (wise107x), LG, Veko, BEKO, Bosch, ARDO, Electrolux Aeg or Zanussi.

Replacing a bearing in a washing machine

We all know how much it costs to repair in a professional company, but despite the high price, if there are no skills in repair work, it is better to contact the craftsmen.

You can remove the drum on the washing machine yourself, without the help of specialists. The decision to disassemble the drum on a home washing machine may come to.

It is quite simple to change the rubber band on the washing machine, but first you should study the theory Replacing the sealing rubber for the drum in.

Before removing the drum, it is worthwhile to study the design of the washing machine.The drum is removed after a precise confirmation of the malfunction or.

Replacing the bearings of the Ariston (Ariston) washing machine

Using the example that is discussed below, the bearings of the Ariston washing machine were replaced. During operation, the rubber seal of the tank begins to let water through, which gets on the bearings, contributes to corrosion and accelerated wear. Average bearing life is 6-10 years.

Before starting repairs, it is necessary to disconnect the washing machine from the power supply and provide access to all its side surfaces. At the first stage, you need to empty the tank and remove it from the machine body. To do this, gain access to the inside by disconnecting the plastic plug located on the back of the machine in the basement area. Unscrew the clamping screw of the clamp that secures the drain pipe to the tank. Disconnect the pipe from the tank.

Disconnect the motor power contacts. Remove the drive belt. The photo on the right (removing the belt) shows another washing machine, but the principle of removing the engine is relevant for other models.

Unscrew, not completely, the two bolts securing the electric motor. Using a hammer handle, gently press on one and the other bolts alternately to slide the engine off the skids. After that, finally unscrew both bolts and, holding, remove the engine.

There is also a heating element in the lower part of the tank. Disconnect the power contacts from it. Also disconnect all wires from the tank. Go to the top of the Ariston (Ariston) washing machine. Unscrew the two screws securing the top cover from the rear wall. Slide the cover back and detach from the body.

Pull out and remove the detergent dispenser. This will allow access to the two control panel mounting screws that need to be removed.

Unscrew the second pair of fixing screws from the top (right and left). Detach the control panel, first from the metering hopper, then the lower part.

READ  How To Remove Mold From Washing Machine

The rubber cover of the hatch (seal) is fixed to the front wall of the washing machine with a metal wire clamp, tightened by a spring. Find the tension spring by moving around the edge of the cuff. Pry off the spring with a flat object, gently pull on it and remove it together with the clamp. Detach the collar from the body of the washing machine. Disconnect the hatch lock by unscrewing the two fastening screws (pictured on the right).

Go to the bottom and detach the plinth panel from the front. We do this using a flat object, prying the top edge of the panel. You now have full access to the front wall mountings of the Ariston washing machine. We unscrew the two screws at the top (right and left) and several screws at the bottom.

Move it up a little and detach the front wall. Access from the front to the inside of the machine. We unscrew the fastening bolts of the front, lower counterweight of the tank (in this example, three bolts).

Disconnect and put aside the lower counterweight. We pass to the upper counterweight, unscrew the mounting bolts and carefully remove it from the seat of the plastic tank.

Unhook and remove the plastic clamp securing the rubber filler pipe to the tank. After that, it will be possible not to disconnect unnecessary elements, but to completely move the metering hopper to the rear wall and temporarily place it there.

Disconnect the level switch (pressure switch) tube from the tank. Thus, it remains to disconnect only the suspension system (shock absorbers and springs). We start with the shock absorbers located at the bottom of the washing machine. The upper end is attached to the tank, the lower to the bottom of the machine. Disconnect the end of the shock absorber that is attached to the tank.

In this model, both ends of the shock are secured with a plastic latch pin. One end of the pin is pointed, the other has a hole. In order to pull out the pin, you can use a self-tapping screw, which must be screwed into the pin hole as shown in the photo.

On the other hand, the plastic pin has a latch that prevents it from moving spontaneously while the washing machine is running. You can compress the latch using a spanner wrench. Then, with one hand, hold the key, with the other, using pliers, gently pull out the pin, holding the screw.

Disconnect the shock absorber from the tank by moving it towards the side wall. Go to the top, namely the suspension springs. With a flat object (in the photo it is a slotted screwdriver), pry off and disconnect the retainer of the upper fastening of both springs.

Check again that all the elements are disconnected from the tank, after which it can be removed from the suspension springs and pulled out of the body of the Ariston washing machine. This must be done carefully so as not to damage the wiring and other elements of the machine that are around the tank. To remove, the tank must be lifted up until the springs are completely loosened and disconnected. Then, carefully sliding it outwards, remove the tank and put it with the cuff down on the supports so as not to damage the plastic elements of the tank.

The second stage of repair for replacing bearings is disassembling the plastic tank of the Ariston washing machine. You need to start by removing the drum pulley. To do this, unscrew the fastening bolt, locking the pulley with a wooden hammer handle or other object. Then remove the pulley from the shaft.

Sometimes this process is difficult, then you need to be patient, and with your hands, along the perimeter, pull the pulley towards you until it is completely removed from the shaft. There is a small part of the drum shaft and an external bearing under the pulley.

Put a wooden block on the shaft, and with hammer blows, knock the shaft out of the bearings. After that, you can proceed to detach the two halves of the tank from each other. To do this, unscrew all the screws securing the two halves around the perimeter of the tank.

After all mounting screws have been removed, carefully insert a wide slotted screwdriver into the slot between the two tank halves and turn it around its axis in several different places. After the gap between the halves increases, separate both halves with your hands.

One of the halves can be easily removed, and from the second you need to remove the drum. If this cannot be done immediately, then you need to put the bar to the drum shaft again and additionally apply several blows with a hammer to the bar, until the drum separates from half of the tank.

After the drum is finally released, it is necessary to check the shaft and bushing (most often it is bronze) for damage. If the washing machine has been operated for a long time with faulty bearings, they could partially or completely collapse and damage the shaft and sleeve. If the shaft or bushing has strong grooves and chips, then the new bearings will not fit tightly on the shaft, and the oil seal will let water through, which will again lead to bearing wear.

Therefore, if the shaft and bushing are in good working order, then they must be thoroughly cleaned of rust and deposits. When cleaning the shaft, you can use fine sandpaper. It is not recommended to use abrasive paper when cleaning the bushing, it may damage the gland. The sleeve is cleaned with the finest abrasive sponge or other means to keep it absolutely smooth.

Also, when inspecting the drum, it is necessary to check the cross, with which the shaft is attached to the drum. The material silumin, from which the crosspiece is made, is sometimes destroyed by the action of an aggressive environment in the tank. Then the rigidity of fastening the shaft with the drum is violated, which leads to noise and vibration during spinning, and in the subsequent and complete destruction of the washing unit.

In this example, the drum shaft with the cross is replaced, since it is damaged (in the photo in the center). The photo on the right shows half of the tank into which old bearings are pressed.

Old tank bearings must be knocked out with a metal bar (such as a chisel) and a hammer. It is more convenient to start with an external bearing (pictured on the left). The chisel should be positioned as shown in the photo, while it is necessary not to damage the bearing mounting seats. When striking, it is necessary to move in a circle so that the bearing does not warp. After removing the outer bearing, turn over half of the tank and knock out the inner one in the same way. The difference between the inner bearing is that the oil seal of the tank will come out with it.

The photo on the right shows new bearings, a tank oil seal and a drum cross with a shaft.

After removing both bearings, it is necessary to remove all deposits and rust from the seats. You can use WD-40 for this. After that, thoroughly wipe everything and grease with Litol-24 grease.

We start installing new bearings from the inner one. We sink it a little with our hands, after which, hitting with a hammer through a wooden block, we plant it below.

To finally press in the bearing, it is necessary, by placing the chisel to its outer edge, to strike with a hammer in a circle. When the bearing stops, it will be heard by the sound of the bumps. Install the oil seal next to the inner bearing. The one shown in the photo consists of a metal shell and a rubber seal that is inserted into the metal.

Install the oil seal assembly next to the bearing and with a hammer blow through a wooden block, seat the oil seal. You need to finally press in the oil seal with a blunt chisel and a hammer, hitting and moving in a circle. After the inner bearing and the oil seal are installed, turn over half the tank and go to the outer bearing.

The photo below shows how the outer bearing is inserted into the bore and the edge is hit with a hammer until it is fully seated. For the final press-in, you can use a chisel, striking only the edge of the bearing while moving in a circle.

After the bearings are installed, proceed to the assembly of the tank, and before that it is necessary to thoroughly clean the joints of both halves and the rubber gasket between them. This example shows that the gasket is installed on the half of the tank that is without bearings.

Apply silicone, waterproof sealant to the gasket and leave for a few minutes. Go to the other half of the tank. Place the drum on a flat surface and put on the second half of the tank, so that the shaft enters the bearings.

After making sure that the shaft is aligned with the bearings, put a pulley on it, as shown in the photo. Screw in the pulley mounting bolt and tighten it to the end, using the wooden handle of the hammer as a stopper. Turn the tank over with the pulley down and connect the tank, while correctly aligning both halves.

After docking both halves of the tank, check the correct and tight fit of them to each other. Screw in all fixing screws around the tank joint. So, the tank is assembled.

For the convenience of further assembly, pre-install and fix the electric motor to the tank, as shown in the photo. Hook both springs onto the tank.

Grasping the tank with both hands, lift it, bring it inside the body and, holding the front edge with your knee, hang it on the springs with your right hand. Install the plastic spring retainers.

Further assembly should be carried out in the reverse order of disassembly, in the same sequence. At the end of assembly, the Ariston washing machine must be checked for leaks in the tank and other connections. To do this, start any of the washing modes and, while illuminating the bottom of the tank and other connections, check the machine for leaks.

Start the first wash at 60-70 degrees without laundry with a small amount of powder to clean the inner surfaces of the tank from the repair grease.

What is required for work?

To get to the “insides” of the washing machine, you have to disassemble it. In addition, the tank is cast in most Ariston models. Therefore, you cannot do without special tools.

To disassemble the washing machine you will need:

  • Screwdrivers (slotted and Phillips).
  • Wrenches with different head diameters.
  • Pliers.
  • Nippers.

To cut and reconnect the tank:

  • Small or mixed hacksaw or metal hacksaw.
  • Drill with drill for 6.
  • Knife.
  • Wrench.
  • Heat-resistant (40-50 degrees), waterproof sealant.
  • Bolts for 2 (5 pieces with nuts).
  • Self-tapping screws (3.5 × 25).

To remove old and install new bearings:

  • Penetrating lubricant.
  • Hammer.
  • Drifts (thin automotive, wide flat).
  • Nylon bristle brush.
  • Rags to remove dirt from the seat.
  • Viscous lubricant (Ciatim 221).
READ  What Water Pressure Is Needed For The Washing Machine

Before starting repairs, the unit must be disconnected from the power supply, shut off the water supply. Place the machine in the middle of the room to provide free access to each side.

Instructions on how to replace a bearing on an Ariston washing machine

by Boris Kornilov 8,569 viewed

What to do when an Ariston washing machine, which has served impeccably for many years, starts to make noise during operation? Abnormal sounds, grinding or knocking are usually caused by wear on the tank bearings. It is clear that for the further operation of the equipment it will be necessary to replace old parts with new ones.

  • What is required for work?
  • Ariston washing machine disassembly procedure
  • Ariston washing machine tank cut
  • Procedure for replacing bearings and oil seal on a washing machine

On the other hand, it is the last point for many that becomes the decisive factor in trying to repair the washing machine with their own hands. over, the high price of professional repair of large household appliances is not always a guarantee of quality.

Ariston washing machine disassembly procedure

Tank hatch seal. We find the spring, pry it with a flat screwdriver and carefully pull out the clamp. Remove the cuff from the front panel, fill it inside.

Cap. We unscrew the bolts located at the back of the unit in the upper part. Remove the cover.

Upper counterweight. In Ariston washing machines, the counterweight is fixed on bolts (older models), which are unscrewed using a key with a 10.

Control Panel. We take out the distributor tray for detergents. Unscrew the 2 inner bolts holding the front panel. Unscrew the 2 bolts on top of the frame. We remove the bar. Disconnect on the right and remove the display board. We take out and put aside the control panel.

Pressostat. Disconnect the connector with the wires, pry the part with a flat screwdriver, detach it from the frame, remove it from the hose connected to the tank.

Dispenser. We unscrew the self-tapping screw located in the upper right corner at the back of the washing machine. We reset the wire connectors. Disconnect the filler pipe from the dispenser. We take out the dispenser together with the valves.

Rear service panel. Unscrew the bolts with a Phillips screwdriver. Remove the cover.

Engine. We remove the belt. Disconnect the power and ground wires from the Tubular Heater. Disconnect the wired connector and ground contact from the engine. Using a key with a head of 10, unscrew the central and 2 side bolts that attach the engine to the tank. We pry the pins with a flat screwdriver, remove the engine, put it aside. We cut through the clamps holding the wires together with nippers. We put it down.

Shock absorbers. We put the washing machine on its side to access the bottom. Using a 10 head, unscrew the bolts from the unit body. Shifting the shock absorbers inward.

Tank drain hose. We squeeze the pipe with pliers, disconnect the hose from the body. We return the machine to its normal position.

Suppressor with power cord. Use a Phillips screwdriver to unscrew the bolt holding the block on the rear wall of the unit. Disconnect the power and ground connectors. Lift the device up a little and take it out. Putting aside.

Tank. We open the door, remove in turn the springs holding the tank to the frame. We take out the tank through the top. We put the hatch upwards on a stable stand.

Disassembly of the washing machine is still complete. To get to the bearings and get the drum, you need to disassemble the tank. Since this part is cast in most Ariston models, the process requires detailed consideration.

Cooking the tool

Begin any work by preparing what may be required. For example, you may need a room or a spacious room in which it will be convenient to disassemble the machine and store parts so that they are easy to find later. Quite often this is the first problem on the way to carrying out the repair of the “washing machine” with your own hands. Having disconnected the machine from all communications and placing it in a convenient place, we prepare the tool. You may need:

  • hammer;
  • pliers
  • flat and Phillips screwdrivers;
  • metal rod;
  • puller for bearings;
  • waterproof grease WD-40;
  • sealant;
  • carob keys;
  • marker.

How to change a bearing in an Ariston washing machine

Replacing bearings in any washing machine, including Ariston, is a rather difficult physical job that requires certain skills and time. Disassembling the machine for the first time, you can spend about two days to do everything in “pure form” with your own hands. Therefore, you will have to stock up not only with tools and detailed text and instructions, but also patience.

We disassemble the machine: take out the tank

By disassembling the washing machine step by step, you can take photos so that you can then collect the equipment back using them. Although this is not necessary, because on this topic, everything is set out in detail and has already been recorded.

So, the analysis of the front-facing Ariston machine is presented in the form of the following aLGorithm:

  • Unscrew the plastic cover located on the back of the case.
  • Unscrew the bolts holding the top cover and remove it.
  • We also remove the back wall of the case.
  • We loosen the clamp on the branch pipe attached to the tank of the washing machine and remove the branch pipe.
  • We take out a chip with wires from the electric motor.
  • Remove the drive belt. In the Ariston machine, it is removed, as in many other “washing machines”, this process is described in detail in the article on how to change the drive belt in a washing machine.
  • Loosen the 2 bolts holding the engine.
  • Gently push the bolts, holding the engine, then unscrew them to the end and take the engine out of the car.
  • Next, disconnect the power supply contacts from the heating element located under the tank.
  • Checking and disconnecting all sensors.
  • We pass to the front part of the case. we take out the powder receiver.
  • Under the powder receptacle we find the bolts holding the front panel, and unscrew them.
  • We unscrew 2 more bolts from above, they also hold the control panel, and detach it.
  • Remove the rubber cuff from the drum.
  • We remove the bottom panel of the case and unscrew all the bolts on which the front wall of the machine is attached.
  • Removing the front of the case.
  • We unscrew and remove the counterweights.
  • Disconnect the filler pipe from the tank.
  • Remove the hose from the water level sensor to the tank.
  • We remove the niche for the powder receiver.
  • Unscrew the shock absorbers.
  • Use a flat screwdriver to remove the spring clips on which the tank hangs.
  • We make sure that everything is disconnected from the tank, and we take it out of the car.

After pulling out the tank of the Ariston washing machine, it must be placed on the supports with the cuff down. Thus, half of the way to get to the bearings is covered. And that’s not the hardest part.

Change the bearing

Now it is necessary to disassemble the plastic tank of the Ariston washing machine. We start by removing the pulley. this is one of the difficult moments, since the pulley is screwed onto a screw with a locking paste. To unscrew it will have to be patient. You can unscrew it with a hammer and chisel, gently tapping on the screw, or you can use a strong T40 bit and holder.

The bit is screwed into the screw shaft, and then, grasping the bit holder, you need to turn the screw counterclockwise. With the help of a marker, you can mark the correct position of the pulley, so that later you can easily put it back on. We remove the pulley by pulling it towards ourselves with swaying movements from side to side. After removing it, you will see the outer bearing and the end of the shaft, which must be knocked out of the tank and drum. This is done like this: a wooden block is placed on the shaft, on which blows are applied with a hammer.

Important! If the shaft does not knock out and a lot of effort is required, then it is best to screw an unnecessary bolt into it, and strike the bolt.

Next, you need to divide the tank into two parts. In some models of Ariston washing machines, they are fastened together with bolts, which can be unscrewed to disassemble the tank. The cuff-side part of the tank can be removed from the drum quite easily. The second part will need to be carefully knocked off the drum so as not to damage the plastic. Having released the drum from the tank, inspect the wear of the shaft sleeve, to do this, wipe it with a cloth and put on a new bearing, if there is even a small play, then the shaft along with the cross will also need to be replaced.

If the tank is not disassembled, but is solid, then it will have to be cut along the seam, how to do this, look in this entry.

And finally, we take on the bearings. First, the outer bearing is knocked out. This is done with a metal rod and a hammer. We rest the rod against the bearing rim and strike a small blow with a hammer, then change the position of the rod and strike again. So we knock down the bearing in a circle. After the bearing is removed, turn the tank over and knock out the second bearing from the inside in the same way. Together with him we get the oil seal.

Note! It is most convenient to use not a hammer, but a special bearing puller. A universal puller can be useful not only for repairing a washing machine.

After pulling out the bearings, we clean them from dirt and wipe the holes where they were inserted with WD-40 liquid to get rid of rust, and then coat with a special grease or Litol-24 grease.

Now we install the bearings, starting with the inner one. Gently drive it in with a rod and a hammer, moving the rod crosswise along the outer rim of the bearing. We put an oil seal on the bearing and coat it with waterproof grease. The outer bearing is driven in the same way. Next, we collect the tank, performing the steps in reverse order, using our own photos or.

Important! When assembling the two tank halves, be sure to clean the joint, insert a rubber gasket, and apply silicone sealant. Then just connect the parts together with bolts.

We also assemble the car in stages, acting in the reverse order. Take your time, be attentive and careful.

In conclusion, we emphasize once again that replacing bearings in any washing machine is considered a rather difficult job. For a better understanding of this work, you can see. presented below. But if after watching. you are even more convinced that you cannot replace this part in the washing machine with your own hands, then feel free to hand it over to the service center.