Error Codes Samsung Washing Machines With Display

Samsung washing machine error codes

Malfunctions of the automatic machine occur due to wear of components, mechanical damage and violations of operating conditions. In the event of a breakdown, a Samsung brand washing machine issues error codes. The most top ones are collected in tables.

Error codes for Samsung washing machines with display

Error codeDecodingReasons for the appearanceWhat to do?
E2Water does not drain from the machine– clogging of the drain pipe;

1.Check the quality of the drain.

Inspect the sewer system for foreign odors.

Check wiring for fire and pump integrity.

4.Replace defective parts.

If such error codes appear for Samsung washing machines:

Check Tubular Heater and wiring.

Inspect thermistor, test its resistance.

Determine the integrity of the Tubular Heater connection and the thermal sensor.

1. See if the hose is frozen.

Inspect the chamber, pressure sensor, air chamber.

Check if there is blockage in the supply valve.

Inspect Control Module.

Reset with the pause and start button.

1. Wait until the amount of foam decreases and continue the program.

Clean the filter. 3. Foam falls out. forced restart. 4. The laundry is removed, the filter is cleaned.

1. Stop the car and open the door. 2.Redistribute the laundry.

Lay things from the same fabric.

1. Checking leaks and sealing damage.

Take out unnecessary things.

Run the program again.

If the machine works. the motor is working properly.

1. Wait until the voltage is normalized.

Continue washing.

If this type of error occurs repeatedly with your Samsung washing machine, install a stabilizer.

Close the sash tightly.

Inspect UBL for debris or items.

Remove garbage and linen.

If the door does not close after all operations, call a specialist.

Press the start and pause button to continue the program.

If the door is not open, you need to press the shutdown button and wait 5-7 seconds.

Turn on the device and check the door on any program.

Press the button and continue washing.

From now on, open the door for adding linen if the water is heated to 50 degrees.

Inspect the drain hose for integrity and replace it.

If water continues to flow out, call a professional.

Place the waste outlet in a tub or container.

Start the desired wash program.

If the code appears again, call a specialist.

Inspect the pressure switch tube or blow it out.

Eliminate kink.

Replace the pipe.

Replace pressure switch.

Press the button several times to return to the starting position.

Wait 15-20 seconds and turn on the device again.

If the problem persists, contact the service center.

Inspect the inlet hose.

Check connection.

Place the hose in the correct position.

If the breakdown persists, call the master.

1. Turn off the device using the button or from the socket.

Unscrew the case.

Test wiring and vibration sensor.

Assemble the car and check how it works.

Replace vibration sensor.

Call a specialist.

Disassemble the device.

Replace capacitor.

Lubricate bearings or blades.

Turn off the washing machine from the network.

Call the master.

Turn off the washing machine from the network.

Call the master.

The indicator will go out when the time becomes

The notification will disappear when the temperature drops.

Press simultaneously the temperature and options selection button.

Hold the key for 10 seconds.

The message will be cleared.

After resuming the electricity supply, press the pause and start button.

Take out excess linen.

If the error persists, call the technician.

Error codes for Samsung washing machines without display

Not all models of the manufacturer’s equipment are equipped with a display. You can identify malfunctions with a Samsung brand washing machine by indicators, using the table with decoding.

Determine by sound whether water is being poured.

In case of repeated error, remove the laundry and check the pressure.

If the pressure is low, check the filter and open the supply valve.

With a strong pressure, clean the filter or restart the machine (turn on after 15 minutes).

Drain water and clean filter.

Spin and rinse the machine.

Remove blockages from the sewer.

Disconnect the drain hose and remove the build-up.

Lead the end of the hose into the tub.

Switch on the device and start the program.

Reconnect the hose to the sewer.

Open the door after 5-7 minutes.

Remove, untangle or add laundry.

Run the program.

Plug it into an outlet directly, not through an extension cord.

Run the program.

Inspect the integrity of parts. a similar error appears with a Samsung brand washing machine when parts are bent.

Remove large debris from the door.

Call a specialist.

Wait for the water to cool.

Reconnect the hose to cold water.

Check drain connection.

Slap the door cover.

Route the hose to a sink or tub.

Turn on the device and continue washing.

Error codes for washing machines Samsung (Samsung)

Samsung has released many lines of washing machine models, and although the error codes for them are generally standardized, the error indication means vary greatly. If with modern Washing machines equipped with a display, everything is simple. an alphanumeric error code is displayed, then earlier models resorted to indication schemes using combinations of lit and blinking LEDs (indicators). In this article we will try to tell you about most of them, including those used in older models.

Since, in general, the Samsung Washing machine uses the same error codes, this article first provides the most complete description of them (in this case, these are models with a display), and then, when listing the errors available for each of the indication schemes and model series, there will be links to the first table.

The order of description is as follows: first, a description of all possible error codes for the Display Washing machine, then for the individual series of Display Washing machines, their specific error set is given, and. errors for Washing machine without display. Since there are a lot of schemes and the article turned out to be long, for ease of navigation, links to the description of all schemes are provided below:

Error codes for Samsung washing machines with display

This table contains codes for all Samsung Washing machine models with a display, therefore, for almost all faults, several codes are indicated at once. In the following sections of this article, for some washing machine lines, their codes will be given. Error codes starting with the letter “E” were used in older Samsung Washing machines.

READ  How To Clean Washing Machine With

We also draw your attention to the fact that several codes may be indicated for one malfunction within the same error numbering system: for example, codes HE, HE1 and HE2 are combined into a general group describing problems with heating water in a tank, although their exact causes are much different. This is done to reduce the description of a large number of error codes; in addition, the details of the errors still mean little to an ordinary washing machine user, and the wizard, whom you most likely call, has more detailed technical descriptions.

The following can lead to the problem:

  • Something is preventing the water from leaving the Washing machine: defect or blockage of the drain hose, blockage of the drain pump hydraulic system. all this you are quite capable of fixing yourself
  • An open in the wiring or the contacts in the circuits from the control controller to the pump or pressure switch have come off; a similar problem may be with the pump motor power supply circuit
  • The drain pump or its impeller has broken: you need to call a specialist to check it and replace the winding or the entire motor
  • The water level sensor (pressure switch) is out of order: diagnostics followed by replacement
  • Control controller failure: professional diagnostics and replacement required if the board is faulty
  • A somewhat exotic situation, but anything can happen: the car was stored in the cold and the water froze in the tank

As you can see, there are many reasons for the appearance of this error code, so it is better to call a qualified specialist. See also “Washer does not wring or empty”

There are many reasons, here are some of them:

  • The mains voltage is too low: if the voltage is really low in the socket. call an electrician
  • First, make sure that the wiring between the temperature sensor or Tubular Heaterm and the control controller is in order, that all pins and connectors are securely attached
  • The absence of a signal from the temperature sensor may mean its malfunction: the faulty sensor is changed
  • Tubular Heater relay “stuck”: it also needs to be changed
  • Heating element (Tubular Heater) burnt out, e.g. due to a thick layer of limescale on it: Replace Tubular Heater only
  • Open in the Tubular Heater power circuit: check wires and contacts
  • Oddly enough, the water may not have time to heat up due to the washing machine in a cold place. rarely, but it happens
  • Electronics problems: temperature sensor, relay, controller

As a result, the electronics block the start of the wash. Possible reasons:

  • First, the most obvious thing: close the door tighter
  • Then we make sure that no objects interfere with the closing of the door: if an error remains, then something is broken
  • Interruption of communication between the UBL control triac (sunroof locking device) and the control controller: ring the circuit, check the contacts
  • Something broke in the UBL, for example, the lock, or the hinges are loose: in principle, the lock can be repaired by yourself, but the UBL. complex block that includes electronics, so it is better to contact the service
  • Door closing sensor faulty: replacement
  • Problems in the UBL control controller: diagnostics and replacement
  • Water does not flow into the Washing machine: the water supply tap is closed, the water supply is weak, the hose is defective or blocked, the inlet valve is clogged, etc. all this you are quite capable of fixing yourself
  • Forgot to close the sunroof door tightly and the electronics block the start of the wash program
  • The inlet solenoid valve has broken: it will have to be replaced
  • Water level sensor (pressure switch) faulty: diagnostics followed by replacement
  • Open in the wiring or loose contacts in the circuits from the control controller to the inlet valve or pressure switch
  • Control controller failure: professional diagnostics and replacement required if the board is faulty

Increased foaming can cause the following:

  • You are using a powder that is not suitable for this washing mode, for example, powder for hand washing has been poured into the washing machine: try changing the detergent
  • Too much detergent has been added: try reducing the dosage at the next wash
  • Water does not drain well from the Washing machine: see error description “5E”
  • The water level sensor is faulty or its circuit is open: ring the circuit, check and replace the sensor
  • The same for the foam sensor, if installed
  • Supervisor Controller Failure: Call Master
  • There may be too much or too little laundry in the tub
  • It is possible that you placed the laundry in the tank incorrectly, which caused an imbalance
  • Washing machine is not completely horizontal: check it on a level
  • The washing machine motor drive belt is damaged: replace the belt
  • Irregularities in the washing machine wiring: ring, fix problem areas, check and tighten contacts
  • Drum positioning sensor defective: diagnostics and sensor replacement
  • The same for the tachogenerator or Hall sensor
  • Something broke in the electric motor: the brushes are worn out, the bearing is seized. call a specialist
  • Control Module Problems: Call Wizards to Diagnose

Problems can be in the following parts of the Washing machine:

  • Inspect all places in the Washing machine where water may leak: inlet and outlet hoses, hatch and its cuff, dispenser, internal pipes, tank
  • The drain pump is leaking: it is unlikely that it can be repaired, it will have to be changed
  • A lot of foam forms: see error description “SUd”
  • Malfunction or open circuit in the control circuit of one of the sensors: pressure switch (water level), leakage control (“Aqua-Stop”)
  • Incorrect installation or error in connecting the drain hose to the sewer
  • Electronics failure

Actually, a somewhat strange grouping of error codes: The washing machine may not turn on for many reasons. See “Samsung Washing Machine Does Not Turn On”. The engine, on the other hand, may not rotate the drum, both due to a malfunction of the triac (it is necessary to check its circuit, the sensor itself and the controller), and because of problems with the tachogenerator (see the description of the “3E” error) or internal motor failures.

  • First, make sure that the wiring between the temperature sensor or Tubular Heaterm and the control controller is in order, that all pins and connectors are securely attached
  • The absence of a signal from the sensor may mean its malfunction: the faulty sensor is changed
  • Tubular Heater relay “stuck”: it also needs to be changed
  • Problems in the control controller: professional diagnostics and controller replacement are required here
READ  Replacement Sunroof Cuff Washing Machine Samsung

The main reasons: poor drainage, breakage of sensors, wrong powder:

  • You are using a powder that is not suitable for this wash cycle: try changing the detergent
  • Too much detergent has been added: try reducing the dosage at the next wash
  • Water does not drain well from the Washing machine: see error description “5E”
  • The water level sensor is faulty or its circuit is open: ring the circuit, check and replace the sensor
  • The same for the inlet filler valve
  • Supervisor Controller Failure: Call Master
  • Something is broken in the fan: repair or replacement
  • The circuit between the fan sensors and the control controller is broken: repair of wiring, tightening of contacts
  • Defective sensors in the fan: diagnostics, repair or replacement
  • Control board failure: call service

The sensor is installed on models of 2013 and later, analogue of a tachometer:

  • The circuit between the sensor and the control controller is broken: repair of wiring, tightening of contacts
  • The sensor is faulty: diagnostics, repair or replacement
  • Control board failure: call service

The washing machine immediately starts to drain water and displays an error code:

  • Installation error: inlet hose connected to hot water
  • Thermostat is faulty or its control circuit is broken
  • Tubular Heater does not work properly: defective, short contacts
  • “Crooked” operating controller

Wi-Fi models only:

  • The dispenser drive or its sensor is faulty: diagnostics, drive repair, sensor replacement
  • Open circuit in the sensor circuit: restore the wiring, tighten and clean the contacts
  • As always, electronics failure is possible

The machine is drawing up too much water

Excess water drawn into the wash tub is indicated on the display by codes E3, 0C, 0F or 0E. The reasons may be:

  • errors in connecting the drain hose;
  • faulty water drain valve;
  • breakage of the water level sensor.

You can remove excess water by turning off the machine, placing the drain hose in the bathroom and starting the wash again.

Common mistakes

Water leak

Water leakage error codes can appear on the display both with a real loss of water, and with a breakdown of the sensor, which transmits an incorrect signal to the control module. The information codes for this error are E9, LC, LE1, and LE.

The causes of a malfunction can be very different:

  • poor connection of the drain hose to the sewer pipe;
  • breakage of the water leakage sensor;
  • leakage in the tank, hoses or seals;
  • pump malfunction;
  • excessive foaming;
  • low position of the water drain hose.

Before starting to inspect the washing machine, be sure to disconnect it from the power supply. Then check the integrity of the hoses, seals, filter and their attachment points. If it was not possible to identify the problem yourself, it is better to contact the specialists.

Error 5d, 5ud, Sud error, as well as SD, SUdS, are associated with excessive foam formation. The reasons for such a malfunction in the operation of the unit may be as follows:

  • the wrong choice of powder for washing or its overdose;
  • poor quality of the used detergent.

If you notice foam coming out of the washing machine, you need to immediately disconnect it from the mains, remove all things from the drum, rinse the powder compartment, filter and the drum itself.

Water supply problems

In this section, we will tell you about the problems associated with insufficient or excessive water supply, improper heating.

Errors caused by such problems are indicated by codes E1, 4C2, 4C, 4E2, 4E and 4E1.

There may be several reasons for improper water intake:

  • water supply hose clogged, kinked or damaged;
  • clogged water supply valve;
  • turning off the water supply in an apartment or house;
  • connection to the washing machine is not cold, but hot water.

To eliminate violations, you need:

  • Check if there is cold water in the taps, if the water supply to the washing machine is closed.
  • Check the water supply hose to the machine: unscrew it and make sure it is not clogged, damaged or kinked.
  • Make sure the machine is connected to cold water, not hot.
  • Inspect the thermal sensor, as well as the place where the hose is connected to the powder compartment (this place is also often clogged).

Power supply problems

If the mains voltage does not correspond to the parameters necessary for the correct operation of the washing machine, codes 9C, 9E2, E91 or UC appear on the display.

The reasons for malfunctions can be different:

  • power surges;
  • lack of electricity in the network;
  • incorrect connection of the washing unit to the network;
  • non-compliance of voltage indicators with device parameters.

Usually, the appearance of the above codes does not require intervention in the operation of the machine. you just need to wait until the power grid indicators stabilize. To protect the device from power surges, you can connect a stabilizer.

Tubular Heater Errors

Another important element of the washing machine is the Tubular Heater (tubular electric heater), which heats the water for washing to the desired temperature. In case of errors in its operation, the display shows codes E6, E5, HC2, HC1, HC, H2, H1, HE3, HE2, HE1 and HE.

Tubular Heater breakdowns are often caused by increased water hardness and lime deposits. When the Tubular Heater is covered with a thick layer of limestone, it stops heating the water and overheats itself, and then fails. You can prevent an unpleasant situation by using special water softeners and periodically cleaning the washing machine, for example, with citric acid. (How to do it right, read this article.)

Other causes of Tubular Heater breakage may be related to:

  • malfunctions in the wiring of household appliances;
  • malfunction of the temperature sensor.

It is not recommended to repair the malfunctions associated with breakdowns of the Tubular Heater on your own. The only thing that can be done is to check if the washing machine is correctly connected to the network.

Washing machine hatch errors

If the washing machine door refuses to close or open, this is usually noticeable without prompts on the display. Errors related to damage to the hatch are displayed on the screen with codes ED, DC2, DC1, DC, dE2, dE1, dE.

The hatch can break for the following reasons:

  • a locked car door was forcefully opened and the lock was broken;
  • foreign objects or debris have fallen into the grooves covering the hatch;
  • there was a failure in the control module of the washing machine;
  • the hatch is warped or deformed during the operation of the machine;
  • the wash was started with a door not hermetically closed.
READ  Samsung Washing Machine Error Le What Does It Mean

If you do not close the door of the machine or your clothes are jammed, the problem can be easily corrected: open the door, put the clothes in the drum and close the door tightly until it clicks. Sometimes, in order to “clear” the error, you need to turn off and on the machine, and then start washing.

With a door that cannot be opened, the situation is more complicated: it is better not to fix such a breakdown on your own, but to contact a repairman. Control module malfunction can sometimes be cleared by turning the washing machine off and then on.

Samsung washing machine error codes: transcript and description

Samsung has established itself as a manufacturer of reliable and high-quality household appliances, including washing machines. An automatic machine is an irreplaceable assistant, therefore its breakdown is a tragedy for any housewife. It’s good that most modern models, for example, Samsung WF-F861, are equipped with a special display, with which you can understand the cause of the malfunction without calling the wizard.

Modern washing machines are designed in such a way that any deviation from normal operation can be recognized by a special code displayed on the display. This encoding greatly facilitates the task of both the repair specialist and the owners of household appliances. Knowing the cause of the malfunction, some errors in the operation of the washing machine can be eliminated quickly and without special training.

Owners of older models without a display, for example, Samsung S821, S852, S1021, find it more difficult to figure out faults. errors in them are indicated by flashing of various indicators.

Of course, error codes do not always accurately indicate the reason for the failure of the unit, but they allow you to determine in which system the failure occurred and check the possible causes of the failure.

In this article, we will look at the error codes of the Samsung washing machine. Please note that for models of household appliances produced by other companies, the decoding of the codes may differ. Error codes on the display can be grouped according to the type of failure.

In the event of a malfunction, manufacturers recommend referring to the operating instructions for the washing machine. There you can also find all informational error codes and their decoding.

If the instructions for the technique are irretrievably lost, they can be found on the Internet. For example, the error codes of the Samsung 6kg WF8590NMW9 Diamond washing machine can be found in its instruction manual.

Errors of the water level sensor (pressure switch)

Error codes for the same problem may vary for different Samsung washing machine models. For example, errors associated with a malfunction of the water level sensor (pressure switch) for the oldest models will be indicated by the code 1EE7, for more modern models, for example, “Diamond”, “Eco Bubble”. E7, 1C, 1E. If you have a Samsung washing machine made in the USA, then error 1E will be indicated as error LE.

The pressure switch in the washing machine detects the water level and sends a signal to the control module. Errors associated with its malfunction consist in the loss of such a connection or improper operation of the element itself. You need to look for the causes of the error in the following:

  • kink, breakage or other damage to the pressure switch tube;
  • breakdown of the relay, contacts or other electronic parts of the pressostat;
  • failure of the entire sensor;
  • faults in the washing machine control module.

When the error E1 is displayed, the washing machine usually automatically activates a forced drain after 3 minutes.

Possible causes of malfunctions can be eliminated as follows:

  • first of all, it is necessary to inspect the sensor. perhaps it will be enough just to clean the contacts, connect the tube or remove contamination from it if it is clogged;
  • if it turns out that the pressure switch is faulty, it must be replaced.

UE, UB, E4

  • The laundry is unevenly distributed over the drum. shift it.
  • Few items. add.
  • Lots of things. turn down.

HE2, H2

This error occurs when the red temperature sensor in the center of the drying heater is triggered (higher than 145 ° C).

Corrective action. lightly press the button in the center. The machine will operate normally. Or replace the sensor if the temperature measurement is incorrect due to functional degradation.

This happens when the steam function does not work normally.

This error does not occur in a Washing machine with a drum. Check if the model supports steam function.

dE, door, DE1, DE2, DC, DC1, DC2, ED

  • Switch contact error due to deformation of the door hook.
  • When a closed door was opened by force.
  • This can happen during a boil cycle if the hatch moves due to pressure drop from internal temperature changes.
  • Replacing the hook of the lock.
  • Do not open a locked hatch.
  • Wait for cooling.

Broken hook on the hatch

For tumble dryers, overheating error

  • Drying temperature sensor breakage.
  • Defective circuits and connectors.
  • Break in Tubular Heater Drying Wiring.
  • Replace sensor.
  • Check circuits and connectors.
  • Repair the wiring.

Engine malfunction

OE, OF, 0C, E3

  • Broken water level sensor.
  • Clogged pressure switch tube or compression chamber.
  • Water is filled in continuously due to a foreign object in the supply valve.
  • Replacing the level sensor.
  • Clean the tube or chamber.
  • Remove debris from the inlet valve.

Water level sensor

Imbalance

LE, LE1, LC, 11E and E9

  • Because of the Tubular Heater (came out of the mount).
  • The air hose is detached and water leaks during spinning.
  • Damage to the tank at the attachment point of the transport bolts.
  • Water leaks from the front with foam due to too much detergent.
  • Connecting hose for detergents not connected correctly.
  • Drain pump filter cover not installed correctly.
  • Through the drain hose.
  • Destruction of sealing washers.
  • The screws that hold the tank and front panel together are crooked.
  • Broken leak sensor.
  • Reinstall the heater.
  • Attach the air hose.
  • If the tank is metal. weld it, in the plastic one. solder it with a repair kit.
  • Reduce the amount of powder used.
  • Check the correct connection of the pipe.
  • Screw on the pump manhole cover.
  • Replace drain hose or install correctly.
  • Replace damaged washers and gaskets.
  • Check screw fastening.
  • Leakage sensor must be replaced.

2H, 3H, 4H

It’s not a mistake. The machine reports the time remaining until the end of the cycle. 2H. 2 hours, 3H. 3 hours, etc.