Connecting The Washing Machine To The Sewer Directly

Siphon for connecting the washing machine to the sewer

You will need a special siphon with two or three taps. If you already have one installed, then you can save money. What is it for? The device creates a water blockage, which prevents “aromas” from the sewer from entering the room.

The advantage of this installation is the ease of cleaning the elements from clogging.

The drain needs to be cleaned periodically. If you have to remove the blockage in the sewer, then the siphon can be easily dismantled and cleaned.

The connection diagram is shown in the picture:

Fix the hose immediately at a level of 50-60 cm from the floor. To do this, use special hooks or clamps. Sleeve length should not exceed 150 cm, therefore it is not recommended to lengthen it. This is due to the efficiency of the pump. Keep the bend in the shape of the letter “S”.

Next, do this:

If possible, install siphons with a non-return valve. They can be built into the wall for an aesthetic appearance.

Preparing to connect the machine

If you are installing new equipment, first decide on the location. Several factors affect the correct connection of the drain hose to the sewer:

  • Drain hole distance;
  • Height and angle of the discharge point;
  • Number of connected devices.

Examine the back of the machine. Where is the hose? If from below, which happens most often, then fix it at a certain height using a grip. Otherwise, water will drain from the tank by self-draining.

It is important that the base under the cabinet is firm and level. Adjust the installation by twisting the feet of the machine. The appliance should not be located far from the drain. The pump will work with redoubled force to pump water over a long distance, and the increased load leads to rapid wear.

How to properly connect the machine to the drain: possible options

There are several ways to connect, but each of them has its own nuances.

Let’s start with the simplest. this is an alternative method of draining through a sink or bathtub. It is enough to put a hook on the hose and hook it over the edge of the sink.

Of course, this method has 0% complexity, but it has a lot of disadvantages:

  • Quick contamination of a sink or bath. Waste liquid contains particles of sand, debris, detergent. All this settles on the walls of the container.
  • If the container is shallow, there is a risk of overflow at high pressure. You will have to constantly monitor the process.
  • Even a child can overturn or pull off the installation.
  • Inability to use the bathroom for its intended purpose during washing.

Important! Choose a hook with a secure fit. It should not jump off the side. When draining, make sure the water drains quickly.

Other connection options require additional tools. What you need:

  • Adjustable wrenches;
  • A set of slotted and Phillips screwdrivers;
  • Pipe cutter or hacksaw for metal;
  • Pliers;
  • Knife;
  • Level;
  • Roulette.
  • Clamps, gaskets, seals;
  • Check valve;
  • Sealant;
  • Rewind.

Other materials depend on the type of connection. There are two options left:

  • Using a sink siphon or special siphon;
  • Using a sewer pipe.

Which way to choose is up to you. We will outline the work in stages, and also point out their advantages and disadvantages.

How to connect a washing machine to the sewer

Buying new appliances means less time will be spent on household chores from now on. Difficulties begin during installation: how to connect the washing machine to the sewer without calling the master? Which way to drain water to choose? It is important to take into account all the nuances so that in the future it is convenient for you to use the device.

Installation of a drain directly to the sewer

In order to lead the hose to the pipe, you will need a special tee and a plastic pipe. Now proceed like this:

  • Take a hacksaw or pipe cutter;
  • Cut the sewer pipe;
  • Put a tee;
  • Seal the attachment point carefully. Poor sealing can cause unpleasant odors in the room.

Connect the sleeve by curving it into an “S” shape. Use an O-ring when connecting.

Important! The height of the bend should be 30-40 cm from the floor.

The stages of the work are shown:

Connecting The Washing Machine To The Sewer Directly

What mistakes users make:

  • Does not secure the hose. During the spin cycle, the machine vibrates strongly, the liquid escapes under pressure. Therefore, the sleeve can simply be torn from its place, which will lead to a flood. Be sure to secure the contacts with a clamp.
  • Narrow siphon. Poor permeability will cause liquid to rise into the sink. Match the element to the width.
  • Long sleeve. This leads to increased stress on the pump when it cannot push water down the drain. Observe the recommended length.
  • Draining water into a shallow sink. The powerful pressure will lead to overflow. Change the way of withdrawal or follow the process.

Each user can do the work. The main thing is to follow the sequence of actions and recommendations of specialists.

Through a siphon

Installation of the connection in this way is special in that we connect the drain hose of the washing machine not to the sewer pipe or its branch, but to another plumbing element. the sink siphon. In modern siphons, manufacturers provide a special outlet for connecting a washing machine, which we should use.

There are siphons with two outlets to connect a washing machine and a dishwasher at the same time.

The essence of connecting a washing machine through a siphon is as follows. We install the siphon and check how the water is drained through the sink drain hole, see that there are no leaks. The siphon can be easily installed by hand without any tools. If you have problems with this, you can read the article Washing machine siphon. installation and connection. Next, we connect the drain hose to the side outlet of the siphon, not forgetting to seal the joint. The hose must be bent with the letter “S”, if this is not done, the first wash will end with the machine hovering in the middle.

Consumables and tools

  • Large and small adjustable wrench.
  • Screwdrivers (flat and Phillips).
  • Plastic pipe cutter.
  • Pliers.
  • Sharp knife.
  • Roulette.
  • Building level.

The set of tools is not rich. It is immediately clear that the entire list can be easily found in any pantry. If you don’t have a tool for cutting plastic pipes, you can use a regular metal hacksaw instead. Now let’s deal with the materials.

  • Drain hose of the correct diameter and length.
  • Plastic sewer pipe and tee for it.
  • Jumpers and clamps.
  • Check valve.
  • Automotive or plumbing sealant.
  • Rewind.
  • O-rings and gaskets.

Before purchasing small consumables, such as O-rings and gaskets, calculate how many you need.

What else matters?

Why are we talking about the quality of the drain, and what’s the difference at all, what kind of connection to the sewer we chose, the main thing is to do everything relatively correctly, and then it doesn’t matter. This is the opinion of many people who independently undertake to connect an automatic washing machine to the water supply and sewerage system and thereby, unwittingly, shorten the life of their “home assistant”. What exactly is it about?

Let us explain with a specific example. We connect two absolutely identical automatic washing machines to the sewer. The first machine is not far away, at a distance of 1 m from the connection point, we connect it using the supplied 1.5 m drain hose, observing all the rules. The second machine is located at a distance of 2.4 meters from the connection point to the sewer pipe or siphon, we connect it using an additionally purchased drain hose 3 m long.

Both washing machines have been in operation for 7 years. The first washing machine worked this time without breakdowns, the second one changed the drain pump 2 times: the first pump broke after 4.5 years of operation, the second in the seventh year of operation. “Debriefing” revealed by many a supposed, but still not uninteresting pattern. The longer the drain hose of the “home helper”, the more often the pump will break down, because when working, it will experience loads that exceed the design.

Place the washing machine as close as possible to the point of its connection to the sewer.

It is also of great importance how the washing machine is installed on a horizontal surface, since this also affects the working life of the pump, engine, as well as working connections of hoses and nozzles, as well as electrical wiring. It is very important here that the washer is not only set at a level, but also stands on a flat, hard surface that will not bend over time and will not loosen from constant vibration.

Various modern additions are also important, which allow, on the one hand, to facilitate the process of connecting the washing machine to the sewage system, and on the other hand, to additionally secure it from some risks, primarily the “siphon effect” When we mention this, we mean drain hoses with a non-return valve. Such a valve is specially designed so that sewage from the sewage system does not under any circumstances fall back into the washer, while the drain will be completely free. You can read about this device in the article Check valve for washing machine.

How to connect?

You can connect to the sewage system, as well as organize the waste water drain of the washing machine, in different ways. Connection is organized depending on a number of factors:

  • on how close the sewer drain is to the body of the washing machine;
  • is there a connection point in the reach at all;
  • at what height and at what angle relative to the washing machine body this point is located;
  • what other equipment will have to be connected to the sewer along with a washing machine, an automatic machine, etc.

The angle of the location of the drain hose in relation to the location of the washing machine is very important to consider. If the hose is positioned incorrectly, a “siphon effect” will occur, water from the sewer pipe will go back into the bowels of the washing machine.

Based on the above factors, there are three main ways to organize a waste water drain for a home assistant. Firstly, the drain can not be organized at all if you throw the drain hose into the nearby plumbing fixtures, for example, the bathroom, sink or even the toilet.

READ  How To Install A Tumble Dryer On A Washing Machine

Secondly, the washing machine can be connected to the side outlet of the siphon. This branch is ideal for screwing the drain hose to it and forgetting about the problem once and for all. And thirdly, the drain hose of the washer can be secured with a clamp by first thrusting such a hose into the branch of the sewer pipe. it’s cheap and cheerful, and most importantly, you don’t need to buy a special siphon with a sink under the sink. We will talk in more detail about how to implement these three ways of draining water a little later, and now we will dwell on the nuances that matter that can affect the quality of such a drain.

Without connection

Now let’s talk directly about how to properly connect our washing machine to the sewer. And, we will start with the simplest option for organizing the drain, which, paradoxically, does not involve connecting the washer to a sewer pipe. Let’s talk about him.

This method is good for lazy people, since it does not require a lot of materials and tools to implement it. And a minimum of time will be spent. However, certain conditions must be met.

  • A sink, a bathroom, a shower cabin with sufficiently high sides, a toilet bowl or trouble should be located near the body of the washing machine at a suitable height.
  • It must be possible to secure the drain hose. Why fix it? And then, so that it does not accidentally jump out of the plumbing element, when pressurized water rushes from the tank of the washing machine through the hose into the drain of the sink, bathroom, etc.
  • People using plumbing should not be squeamish, because they will have to endure some inconveniences that will appear in connection with such an organization of draining water from the washing machine tank.

To organize the drain in this way, you need to lower the hose of the machine into the bathtub, sink, toilet, etc. not tight. Provide an S-shaped bend in the hose. Fix it to the wall of the plumbing element so that it does not dangle freely, and then carry out tests. If the drain is carried out normally, you can leave everything as it is, the work is over.

How to connect the drain hose of the washing machine to the drain

How to connect the drain hose of the washing machine to the drain? Everything seems to be simple, you just take it and plug it in, but it wasn’t there. Incorrect installation of the washing machine drain hose can lead to a number of problems in the near future. Even with such a simple action, one cannot neglect the simple rules for connecting a washing machine, which we will talk about today, despite the fact that there are not so few ways to do this.

Directly into the sewer pipe

You can also connect the washing machine to a nearby sewer outlet. For this, such a diversion must be organized. We do the following.

  • We purchase a tee for a sewer pipe.
  • Using a pipe cutting device, we cut a plastic sewer pipe.
  • Install the tee, seal the joint.

Well, the pipe branch is organized. In this case, it is very important that the branch is located at a height of at least 40 cm from the floor level. We insert the end of the drain hose into the pipe bend and seal the connection. We strengthen the connections additionally with a clamp so that the pipe does not accidentally jump out of pressure and flood the entire floor. We bend the hose with the letter “S” and fix it so that it does not dangle.

, We note that it is really easy to connect the washing machine to the sewer if you follow the simplest instructions that have long been formulated by experts. You can do that too. Read this article and get started, good luck!

Required tools and accessories

To connect the washing machine to the sewer, you need to have three tools at hand:

  • Pliers.
  • Flat screwdriver.
  • Pipe cutter for plastic pipes (or a hacksaw for metal).

Wrenches may only be needed if it is necessary to extend the existing drain hose with a coupling. This will have to be done when the machine is far away from the sewer outlet. At the same time, it is highly not recommended to extend this flexible drainage bend to a length of more than three meters. With its long length, the pump in the washing machine may not cope with pumping water and burn out.

Required adapters and taps for connecting a washing machine

Consumable components will require:

  • sealing gum;
  • sealant;
  • corrugated hose (usually supplied with the washing machine);
  • tee or new siphon (depending on the connection option).

To connect the drain of the washing machine to the sewer, a minimum set of tools and accessories is enough. The same replacement of electrical wiring or installation of water pipes requires much more tools.

Washing machine connection diagram

Other ways to drain

You can also drain the washing machine directly into a bathtub, sink or toilet. For this, almost all household appliances under consideration have a rigid plastic nozzle for the drain hose. It is designed to fix the drain hose on the side of the above-mentioned plumbing fixtures.

Installation and assembly of the washing machine drain

The main advantage of this connection is simplicity. However, the plumbing will have to be washed after each automatic wash, since the water from the washing machine goes into the sewer system by no means crystal clear. Plus, because of the high pressure, some of the drains can pour out of the sink or toilet bowl onto the floor. Then you have to clean up the entire bathroom.

By reducing directly to the sewer

To connect the washing machine directly to the sewer, you need to install a tee on the drain pipe under the sink or bathroom. One of its taps will be used in the old way for the connected plumbing, and the second will go for the washing machine. You can also make a tie-in directly into the sewer pipeline or mount a branch from the riser. But these options are more complicated, it is worth resorting to them only when carrying out major repairs.

How to install the washing machine correctly

The drain from the machine is inserted into the tee through a rubber sleeve. This adapter has to be used, since hoses from washing machines and plastic fittings for PVC sewer pipes for internal sewage have different diameters. If you simply insert the drain branch into the tee, then the drains under pressure will go out of the pipeline through the gap at the junction.

Washing machine drain connection

Siphon connection

It is only possible to connect the washing machine to the sewer with a drain siphon if it is designed for such an installation. If it does not have a side outlet for connecting an additional hose, then nothing will come of it. Or it will come to be changed to the desired option.

How to connect a washing machine via a siphon

over, if the cabinet under the sink is small in size or the sink is on a narrow ceramic leg, then it will not be possible to drain through a siphon with a branch pipe on the side. There will simply not be enough space under the bowl for new pipes.

Rules for installing a washing machine under the sink

The connection is made via a siphon as follows:

  • The plug is removed from the side pipe.
  • It is lubricated with silicone.
  • A hose from the washing machine is put on the outlet, over which a worm clamp is pulled.
  • The clamp is tightened with a screwdriver or pliers.

How to connect a washing machine to the sewer and plumbing in the kitchen

The main disadvantage of this method is gurgling in the sink drain when the washing machine is running.

Connecting the drain of the washing machine to the sewer

Installing a machine for washing clothes in the house includes connecting it not only to the power supply and water supply, but also to the sewer system. over, it is with the drain that difficulties often arise; it is as easy as shelling pears to connect the considered household appliances to the power supply and water. To independently connect the washing machine to the sewer, you can use three methods. The technology in all cases is extremely simple. Any self-taught person can do everything, you just need to follow the simplest rules.

Methods

The washing machine is connected to the sewer system:

  • directly to the sewer pipe through a tee;
  • through the siphon connection under the sink.

The first option is more difficult to implement with your own hands, but it is more practical and reliable. Plus, the risk of flooding when connected to a siphon is much higher than in the case of a direct connection of the drain hose and sewer pipe.

Prerequisites for connecting a washing machine to a siphon

At the same time, it is recommended to choose a method even when the question of how to make a sewage system in a house or apartment is being decided. It is better to determine in advance the place for the washing machine. And also in advance it is necessary to provide for this technique a tie-in point in the sewer system.

Another way to organize the drain from the washing machine is to simply hang the hose on the side of the toilet or bathtub. In this case, even installation tools are not required. But this option is difficult to call correct. Plus, you will have to look after such a water drain more carefully in order to surely avoid a flood in the house.

Washing machine connection

You do not need to have special knowledge, skills and special tools to connect a washing machine to a sewer pipe. Almost any beginner master is able to do everything correctly. To figure out how to dissolve the sewage system in a private house or apartment, it’s difficult. And independent connection to the existing drainage system of the automatic machine should not cause problems.

It is hardly worth paying even a few hundred rubles for such work to a professional plumber on call. If he is invited as part of the overhaul, then let all the equipment in the bathroom or in the kitchen connect. A newly purchased washing machine can be connected to communications and.

Third way

To connect the washing machine to the sewer system in compliance with all requirements and rules, it is necessary to take into account some features:

  • The drain hose of the automatic washing machine has a diameter of 22 mm. However, water pipes with a cross section of 50 and 32 mm do not have bends with a special socket. For this reason, a rubber reducer is used as an adapter for draining the washing machine into the sewer, with which you can connect the drain hose to pipes of various diameters. The device is distinguished by an acceptable price, ease of installation and tightness.
  • When the unit is located in close proximity to a sewer pipe with a diameter of 50 mm, the washing machine is directly connected to the sewer through a tee.
  • If the distance from the junction of the hose to the sewer pipe is too great, then it is recommended to connect using a PVC pipe with a diameter of 32 mm, connecting it to the branch pipe with a diameter of 50 mm.
  • Forced draining of water in automatic washing machines allows you to lay a pipe with a diameter of 32 mm without additional slope.
  • When connecting pipes of different diameters, it is recommended to use a rubber reducer.
  • Some models of washing machines are equipped with a drain hose, which has a diameter of 19 mm on the side of the household appliance, and 22 mm on the side of the sewer pipe.
READ  How To Position The Washing Machine In The Bathroom

Connecting the washing machine to the sewer. options and connection rules

The problem of connecting an automatic washing machine to the sewer system is solved in several ways, each of which has its own characteristics.

Some subtleties of connecting an automatic machine

To properly connect the drain of the automatic type washing machine to the sewer system, first of all, it is necessary to install the presence of a check valve on the household appliance. This structural element allows fluid to move in only one direction.

If a check valve is not available, consult the manufacturer’s information regarding the height at which the hose loop should be held when draining to create a water seal. You need to understand that the drain height for the washing machine. quite an important point. The water seal acts as a check valve to some extent and prevents unpleasant odors from the waste pipes from entering through the machine.

Modern automatic machines for washing clothes are equipped with a non-return valve, so when connecting household appliances there are no problems with connecting the drain hose. The process of solving the issue of how to properly connect the washing machine to the sewer involves connecting a smooth end pipe and a rubber reduction or connecting it to an additional siphon outlet.

Any liquid detergent helps to facilitate the process of connecting individual elements into a single structure. They lubricate the rubber reduction, which makes it easier to insert the smooth part of the branch pipe into it, and directly pack the reduction into the socket.

When connecting the drain hose using an additional outlet in the siphon, it is necessary to remove the tube from the hole, which the manufacturer installs to maintain the parts in working order. After that, you need to insert the smooth end of the hose. A special coupling is responsible for the quality of the connection, which presses the tapered gasket. This arrangement provides a reliable seal.

In some situations, it becomes necessary to extend the drain hose, for example, if the standard length is not enough to connect the hose to the sewer pipe in a certain place. In this case, take an additional piece of the appropriate length and connect it to the main hose using a fitting with a safety net and steel clamps 1627 mm. To connect hoses of different diameters, use special fittings with different branch pipes.

You can also use a modular element, which consists of a segment about half a meter long. With this hose, you can make a connection at any distance. However, it should be understood that with a longer drain for the washing machine into the sewer, it will be more difficult for the pump to cope with the water supply.

First option

The simplest solution to the issue of how to connect the washing machine to the sewer is not a direct connection to the system. It is enough to fix the drain hose over the side of the bath with a U-shaped element, which manufacturers equip almost every automatic washing machine.

The second way to connect the washing machine to the sewer

The siphon is usually equipped with a plug. It can close an additional hole if, due to some circumstances, the automatic type machine will not be connected to the siphon.

Plumbing connection

It is much easier to connect an automatic washing machine to a water supply than to a sewer pipe. The main condition is the presence of a water pipe with shut-off valves in the immediate vicinity of the machine. The hose of the machine is equipped with two clamping nuts, therefore, a nipple with an external thread is required at the connection points. In this case, it is very important that the diameters of the nuts and shut-off valves match. Otherwise, the connection may require the use of a reducing fitting.

Connecting the washing machine to the sewer and plumbing system can be done independently, provided that all measures are correctly and accurately performed. The main condition is to achieve complete tightness of all joints.

We prepare tools and accessories

Any serious work requires careful preparation, connecting the washing machine to the sewer is no exception. If you have to install an old car after moving, organizing water drainage, then some tools and accessories may be required, and when installing a new machine, some of the accessories are already included in the attachment with the machine.

But you need to start preparing by determining the installation site. There can be three options:

  • In the bathroom, which is very convenient, since any outlet, including the drain, is almost at hand.
  • In the kitchen next to the sink.
  • In the hall.

Having determined the location, prepare the tools so as not to search for them, organizing a bend. You may need:

  • various screwdrivers;
  • keys;
  • the pipe cutter, if necessary, cut into the drain pipe;
  • welding for metal-plastic pipes;
  • conventional siphon or with a check valve;
  • plastic tee;
  • silicone sealant;
  • sealing gum;
  • drainage corrugated hose of the required length if the factory is too short.

Note! It is not recommended to dock the hoses, as additional connections pose additional risks of water leaks. The optimal hose length is considered to be no more than 3 meters, because the longer the hose, the greater the load on the pump, the drain should be closer.

Another step in preparing the washing machine for connection is dismantling the shipping bolts. When the machine is fully prepared for connecting to communications, you can proceed to the main work.

Connecting the washing machine to the sewer

In the process of installing and connecting the washing machine, the task arises of how to organize the drainage of waste water correctly. The most correct way is to connect the drain hose directly to the sewer branch, but it is also the most time consuming. We will describe how to organize the drain in detail and start with the preparatory work.

Sewer connection methods

Before organizing the drain and connecting the washing machine to the siphon, you must install the siphon itself on the sink. If the siphon does not have a separate outlet for household appliances, then a plastic tee will also need to be connected to it. With such a connection, an unpleasant smell from the sewer can enter the drum, where after the wash cycle the laundry lies.

Therefore, it is necessary to organize an “air barrier” in the siphon. For this, the siphon has a special branch to which a corrugated pipe is connected. It is curved in such a way that water stagnates in its bend, creating a reliable plug that does not let odor from the sewer into the tank of the machine. At the same time, such a plug does not complicate the drainage of waste water from the washing machine to the drain and is updated with each descent of water into the sewer.

Instead of a simple siphon, you can use a siphon with a check valve, which prevents not only odor, but also waste water from entering the machine, in this case, it is possible to organize the drain much more efficiently. If the siphon is clogged, a situation may arise when waste water fills it and flows back into the machine by gravity. To prevent this from happening, a valve is built into the siphon.

After installing the siphon, you need to connect the hose to the branch from the siphon. It’s easy to do, just fasten the clamp.

In some cases, the drain hose of the washing machine is not connected through a siphon, but into a branch of the sewer pipe. In this case, an O-ring adapter is required. This adapter will allow you to insert the hose into the wide opening of the pipe. This method is more labor intensive than the previous one. However, it is reasonable to use it when the washing machine is placed more than 2 m from the sink siphon.

The photo shows a direct connection without using an adapter siphon tube (left) and using it (right). Such an adapter allows you to create an air congestion, which prevents odors from entering the machine from the sewer.

When organizing the drainage of waste water from the machine through a siphon or directly, the distance from the floor to the drain point must be taken into account. The point at which the end of the hose will be located must be at least 50 cm above the floor. The maximum height from the floor to which the drain hose can be lifted is no more than 100 cm.These figures depend on the capacity of the drain pump.

Connecting the drain hose of the washing machine through a siphon or directly to the sewer is considered the most reliable way to organize the drain. The risk of water leakage is minimized if the hose is accidentally touched. In addition, from an aesthetic point of view, this is also the best option, since the hose is usually hidden behind the machine itself or the kitchen set.

Other ways to drain waste water

The simplest options for organizing the drain of water from the washing machine is to throw the drain hose through the sink, bathroom or toilet. To do this, you need a plastic hook-shaped nozzle that will hold the hose on the sink or bathtub.

This way of organizing the drain is the most unreliable. And it has a number of disadvantages:

  • the pressure of the water can rip the hose off the side of the tub, and all the water will spill out onto the floor. In addition, pets and small children can also rip off the hose.
  • after each wash, you will have to thoroughly clean the bathroom, sink or toilet.
  • this method of draining is not aesthetically pleasing, especially for the sink, because pouring waste water into the sink after washing socks and underwear, and then washing dishes in this sink is at least not hygienic.

Important! If, nevertheless, it is decided to use this method of draining water from the machine, then remember that the length of the drain hose should not exceed 4 meters, since a larger volume of waste water can remain in the hose itself and stagnate in it, emitting an unpleasant odor.

READ  The Washing Machine Does Not Turn On LG Reasons

Thus, you can connect the washing machine to the sewer yourself, if you have the desire, tools and time. And do not save on components, because a reliable and competent connection is the key to a trouble-free and uninterrupted operation of the washing machine.

Draining water into the bathroom and toilet

One of the most common ways to drain dirty water is by attaching a hose to the side of the plumbing. However, with a strong water pressure, the toilet lid may not hold the device, as a result, it breaks off and heavily floods the bathroom floors.

If the hose is in the wrong position, the toilet lid can also open slightly, and the hose can slip off the side. The same actions occur if the surface of the plumbing is unstable. To avoid a flood, the outlet must be fixed on the side with a plastic hook included in the machine kit.

The advantage of this method is the ease of connection to the water drain system. People do not have to fiddle with pipes and siphons when connecting. In addition, the height of the bath side often varies from 60 cm to 80 cm.However, such a vending machine drain system in the bathroom has a number of disadvantages.

How to connect a clipper without using a siphon

It is not difficult to make a direct connection to the sewer, the main thing is to use a tee and follow all the rules for height. A tee with a diameter of 50 mm is installed in the socket of a plastic sewer pipe.

A plastic or polyethylene tee is mounted as follows:

  • first you need to pull out the old siphon;
  • then insert the adapter;
  • after that, the tee itself is installed.

Sometimes it is necessary to use an additional plastic tube to connect to the sewer. How to connect the drain system directly to the sewer?

It is not difficult to install such a drain system in the bathroom:

  • first you need to lower the hose into the pipe;
  • then fix;
  • and after. tightly connect.

With a leaky connection, sewer odors will penetrate into the room.

It is not for nothing that the back cover of the washing machine is equipped with a special fastener for the hose, which is located much higher than the area from which the hose is taken out. If it is in the correct position, even when the pump is turned off, dirty water is not refluxed into the machine. If the cover does not have such an attachment, you should independently carry out the S-shaped bend of the hose.

It is worth noting that a straight hose can always lead to a reverse throw of dirty water, and even well-washed laundry can smell like sewage. Therefore, it is so important to correctly position the hose. The adapter is used to improve sealing.

By the way, the same actions are performed when the hose needs to be replaced. Then the back cover is removed and the hose to which the drain pump is connected is replaced. Some washing machines are designed in such a way that when replacing the drain hose, the top cover of the machine must also be dismantled, which after replacing the hose is reinstalled.

Connection height

When connecting the drainage system, it is imperative to observe such a parameter as height. The drain pump has limited power, so the hose must be located at a height of 80 cm by the machine itself, and at the sewer from 60 cm or higher.

If the hose is positioned lower, the pump of the machine can quickly wear out. Also, manufacturers do not recommend lengthening the hoses by more than one and a half meters, or using low-quality materials. the drain pump may work slower or break.

The end of the hose, located at a level of 60 cm from the floor or higher, must be led out into the sewer outlet, and fixed with a cuff or elastic band measuring 3.2×4 cm overlapping with the pipe. When connecting to a branch, the hose must not be in the water.

If the branch is not equipped with a non-return valve. with an S-shaped connection, this effect can be achieved due to the air gap. The lowest part of the hose should be located 50 cm from the floor or higher. If the sewer pipe is below 50 cm, when connecting the drain system without a siphon, a “siphon effect” can be created and a sewer smell can constantly occur.

Draining methods

Some people prefer to install large equipment without the help of specialists. Such actions help them save on wages for the foreman, and will fully ensure the quality of their work. It is believed that to drain dirty water during washing, it is enough to place the drain hose in a bathtub or sink. This is not true. It is much better to connect the machine to the sewerage system using the necessary equipment.

When connecting, do not twist or squeeze the drain hose. this will impede normal water flow.

Basic connection methods
Connection typeBenefitsdisadvantages
Connection via siphon outletReliable and secure connection, open parts can be covered with a decorative panel.It may be difficult to connect to the siphon if it is too far away
Direct connection to the sewerUse if the siphon is too far from the machine.Complexity of connection
Hose outlet to plumbingThe easiest way to connect. The height of the sides of the plumbing does not affect the drain in any way.There is a high risk of ripping the drain hose off the side of the tub or sink and flooding the floor

Direct drain into the sewer for the washing machine

Reliable and safe draining of the washing machine is achieved due to its correct connection to the sewer. How to connect it to the sewer yourself and not encounter breakdowns due to improper connection?

Disadvantages of plumbing drain

With such a drain, plumbing is constantly in contact with dirty water. Rarely does water penetrate directly into the drain. Usually, the edge of the hose only reaches the edge of the plumbing bead. When such a drain is made, the flowing water constantly contaminates the plumbing. The drain diversion into the toilet does not make it possible to use the toilet normally, which leads to additional inconveniences.

One of the most important drawbacks is the inconsistency of the drain hose from the edges of the bathroom fixtures. This damages floors and floods neighbors. over, the hose falls both from the carelessness of the users, and from strong vibrations when rinsing or spinning. When the pump turns on, it can also break. This is due to the strong water pressure.

The methods of connection through a siphon or directly into the sewer are devoid of such disadvantages. The complexity of the connection is justified by tightness, excluding water leakage, cleanliness of plumbing and the presence of unpleasant odors.

Sewer connection with a siphon

For this method of connecting the drain system, a siphon must be installed high under the sink. This will exclude the return of water to the machine. It is not easy to connect a drain under the sink, if the drain hose is short, then it needs to be lengthened. The maximum size is indicated in the instructions for the machine. The only drawback of elongation is the increased load on the pump. An additional section of the hose promotes increased water flow, the pump wears out faster.

The plastic siphon is equipped with a branch pipe to which the hose is connected. This connection must be fixed with a sleeve in order to exclude the penetration of unpleasant sewage odors into the machine and to seal the connection. The drain connection facilitates the penetration of water into the drain pump.

With the help of such a connection, dirty water is drained into the sewer without hindrance. There is no water leakage under the siphon above the floor. This is due to the sealing of the siphon with a rubber cuff.

In the bathroom, you can safely do what is required, since the sink or toilet is not occupied by the hose. Water flows directly into the sewer through a siphon. The only thing that may bother you is the slightly gurgling liquid penetrating through the drain pump and in the neck of the sink.

How to install a siphon

Often people think about which siphon to use for a washing machine, and how to connect it. Ideally, the new siphon is equipped with a branch pipe to which the water drainage hose is connected. First, the product is connected to the neck of the sink. Install it not horizontally, but vertically. Failure to observe this rule may result in leaks.

The position and height of the connection also play an important role. Where the rear cover is located, the drain hose must be at least 60 cm high. The drain system may be lower. The back cover of the washing machine is usually equipped with a special fastener at the top to which you can attach a hose to drain the water.

Some experts believe that the system should not be tightly tightened, believing that the clearances allow you to exclude a partial reflux of dirty fluid. This does not always work, so the system must be sealed. To prevent backflow, a special valve called an anti-siphon is used. After installing the siphon, you need to open the tap to check the connection.

After that, the drain hose is connected using a cuff or adapter. If there is no cuff, then for tightness the adapter must be tightened with a clamp at the junction. Often people use siphons that can be built into walls. One part of such a siphon is directed to the sewer pipes, the second is outward, to which a drain hose is connected and tightened with a clamp. For the fastest possible connection of the machine, a cold water outlet is installed nearby.

If you do not want to connect a drain system with a siphon in the bathroom, you can connect the machine to the sewer directly.

How to connect a drain in a private house without sewerage

At the dacha or in a private house there may be no sewerage system, then the drain is made “overboard” If there is no sewage system in the house, it is impossible to place a drain hose up to 500 cm long on the floor. The long hose collects an amount of water commensurate with the volume of liquid in the drum. Therefore, water can constantly be poured and drained.

At the dacha, it is not difficult to install a drain system, just install a large water tank and lower a hose into it. For pressure, 2 tanks with water are installed on the 2nd floor of the house.

If there are no large tanks at the dacha, and the water pressure is too low, you should think about purchasing a pumping station. This is necessary, because weak water pressure leads to damage to the washing machine.